SanDisk
SanDisk Cruzer Blade 8 GB USB 2.0 USB flash drive Black SDCZ50-008G-B35
US$391.99
0.00502107BTC
재고 있음
Computer Memory Solutions
Computer Memory Solutions 512MB DDR 333 SODIMM 100-Pin memory upgrade
512MB DDR 333 SODIMM 100-pin memory upgrade for Kyocera FS-1100, FS-1300D, FS-C5015N, FS-C5020N, FS-C5025N and FS-C5030N printers
- Capacity512MB
- SpeedDDR 333 (PC 2700)
- CAS LatencyCL2.5
- Timing3-3-3
- Voltage2.5V
- ECCNo
- 512 MB DDR 333 memory adds capacity to supported Kyocera printers
- DDR 333 (PC 2700) speed matches original system timing for stable operation
- CL2.5 CAS latency with 3-3-3 timing delivers responsive data access
- 100-pin SODIMM form factor fits the designated Kyocera FS and FS-C models
- Unbuffered 2.5 V design installs directly without extra configuration
Compatible Kyocera Printer Upgrade
This 512MB SODIMM module is built for Kyocera FS-C5015N, FS-C5020N, FS-C5025N and FS-C5030N printers. It also supports FS-1100 and FS-1300D models. The stick adds memory to the listed devices for print-job buffering and font storage. It is not for desktop or laptop motherboards.
Simple SODIMM Installation
The 100-pin SODIMM slots into the printer's memory socket without tools. Align the notch, insert at an angle, then press down until the clips latch. A common issue is seating the module fully; if the printer does not recognise the new capacity, remove and reseat the stick. No BIOS or driver updates are required.
512MB Capacity Limit
Each socket accepts a maximum of 512MB, and the system supports two sockets for a total of 1GB. This single module fills one slot completely. Installing a larger stick will not work because the controller cannot address more memory per socket. The 333MHz DDR speed matches the printer's bus.
주요 특징
- 512 MB DDR 333 memory adds capacity to supported Kyocera printers
- DDR 333 (PC 2700) speed matches original system timing for stable operation
- CL2.5 CAS latency with 3-3-3 timing delivers responsive data access
- 100-pin SODIMM form factor fits the designated Kyocera FS and FS-C models
- Unbuffered 2.5 V design installs directly without extra configuration
사양
| Brand | Computer Memory Solutions |
|---|---|
| Model | CM512MBPC2700100PIN |
| Capacity | 512MB |
| Speed | DDR 333 (PC 2700) |
| CAS Latency | CL2.5 |
| Timing | 3-3-3 |
| Voltage | 2.5V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major Brand Chipset |
| Heat Spreader | No |
| Compatible System | Kyocera Fs-C5015N, Fs-C5020N, Fs-C5025N, Fs-C5030N |
| Package Content | 1 Memory RAM Stick |
이 상품에 대한 질문
How can I confirm the 512MB DDR 333 SODIMM is recognised by my Kyocera FS-C5025N after installation?
Power on the printer and check the system information menu; it should report the total memory as 1GB when both sockets are filled with 512MB modules.
What comes in the package and do I need any extra parts to install the 100-pin SODIMM?
The box contains one 512MB DDR 333 SODIMM stick; no additional components are required for installation.
Which capacity should I choose if my Kyocera FS-1300D has two sockets and a 1GB maximum?
Select the 512MB module; two of them will reach the 1GB limit supported by the printer.
이 진열대의 다른 상품
고객들이 함께 비교한 상품
같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.
