Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Rectangular metal fan module with side vents and rear label

HPE Juniper Networking

HPE Juniper Networking EX3400 Fan Module Back-To-Front Airflow

SKU CH-VSTM-C84AD

Fan module provides back-to-front cooling for EX3400-24P, EX3400-48P, EX3400-24T and EX3400-48T switches

  • Keeps switches cool with back-to-front airflow design
  • Reduces noise by running at moderate speed normally
  • Automatically increases fan speed when chassis temperature rises
  • Compatible with EX3400-24P, EX3400-48P, EX3400-24T, EX3400-48T models
  • New factory-sealed module with part number EX3400-FAN-AFI

Fan Module for EX3400 Switches

This Juniper Networks fan module provides back-to-front airflow for the EX3400 series. It pulls cool air into the chassis and exhausts heat from the front panel. The unit suits network administrators deploying EX3400-24P, EX3400-48P, EX3400-24T, or EX3400-48T switches in standard hot-aisle or cold-aisle layouts.

Replacement Cooling Unit

The module replaces a failed or missing fan tray in compatible EX3400 switches to restore proper thermal management. A swap is warranted when the original unit develops bearing noise, reports a fault LED, or cannot spin up under rising internal temperatures. It is not suited for front-to-back airflow racks or non-EX3400 chassis.

Chassis Integration

The fan unit slides into the dedicated slot on supported EX3400 models without tools. Temperature sensors in the chassis govern automatic speed control, ramping rotation only when heat loads demand it. This behaviour keeps acoustic output low during typical operation while freeing rack space otherwise needed for external cooling ductwork.

Priekšrocības

  • Keeps switches cool with back-to-front airflow design
  • Reduces noise by running at moderate speed normally
  • Automatically increases fan speed when chassis temperature rises
  • Compatible with EX3400-24P, EX3400-48P, EX3400-24T, EX3400-48T models
  • New factory-sealed module with part number EX3400-FAN-AFI

Specifikācijas

SeriesEX3400

Jautājumi par šo preci

Does the EX3400-FAN-AFI module fit the EX3400-24T and EX3400-48P switches?

Yes, this fan module is compatible with the EX3400-24T, EX3400-48T, EX3400-24P and EX3400-48P models.

How do I install the fan module so the back-to-front airflow works correctly?

Slide the module into the chassis slot until the latch clicks; the unit pulls cool air from the rear and exhausts it out the front.

When should I replace the EX3400-FAN-AFI unit?

Replace the module if the fans run constantly at high speed, produce unusual noise, or the chassis temperature sensor reports overheating.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.