Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Green circuit board with M.2 slot, PoE header, and cooling fan

KEHIPI

KEHIPI PoE M.2 HAT+ NVME Adapter for Raspberry Pi 5 2230/2242

SKU CH-NHCS-01ZC9

Adds NVME M.2 2230/2242 storage and 802.3af/at PoE to Raspberry Pi 5 via 16-pin PCIe with 5 V 4.5 A power output

  • Boots Raspberry Pi 5 from NVMe SSD via 16-pin PCIe
  • Powers Pi and SSD through single Ethernet cable using 802.3af/at PoE
  • Delivers up to 4.5 A at 5 V with 25 W total budget
  • Accepts 2230 and 2242 M.2 drives for flexible storage choice
  • Stackable 40-pin GPIO header keeps expansion options open

NVMe HAT+ for Raspberry Pi 5

The KEHIPI PoE M.2 HAT+ adds a 16-pin PCIe M-key slot to a Raspberry Pi 5, accepting 2230 or 2242 NVMe SSDs. It draws power from the 40-pin GPIO header and includes an EEPROM for automatic board configuration. Makers and embedded engineers can boot the Pi 5 directly from solid-state storage.

Sustained operation with PoE and cooling

The board delivers up to 4.5 A at 5 V, with a combined 12 V and 5 V ceiling of 25 W, while an onboard fan manages thermals during continuous NVMe traffic. Power over Ethernet follows 802.3af/at, supplying both data and power through a single cable so the system remains stable under prolonged I/O load.

Gen2 and Gen3 PCIe limits

The adapter operates in Gen2 or Gen3 mode depending on the installed SSD and Raspberry Pi 5 firmware. Builders needing Gen4 throughput or drives larger than 2242 will find the interface does not support those configurations. No wireless or Bluetooth circuitry is present on the HAT+.

Priekšrocības

  • Boots Raspberry Pi 5 from NVMe SSD via 16-pin PCIe
  • Powers Pi and SSD through single Ethernet cable using 802.3af/at PoE
  • Delivers up to 4.5 A at 5 V with 25 W total budget
  • Accepts 2230 and 2242 M.2 drives for flexible storage choice
  • Stackable 40-pin GPIO header keeps expansion options open

Specifikācijas

Brandwaveshare
ModelPoE M.2 HAT+
Part NumberPoE M.2 HAT+

Jautājumi par šo preci

How much power does the HAT+ fan and PoE circuitry draw when the Raspberry Pi 5 runs continuously?

The board delivers up to 4.5 A at 5 V with a combined 12 V and 5 V limit of 25 W, so sustained load stays within that envelope.

What must I already own to boot from an M.2 drive using this adapter?

A Raspberry Pi 5, a 2230 or 2242 NVME M-key SSD, and a PoE switch or injector compliant with 802.3 af/at.

Will the 40-pin header on this HAT+ still let me stack my older HATs on top?

Yes, the standard 40-pin GPIO stackable header is exposed, so existing HATs can be mounted above this board.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.