Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Green development board with dual male headers and rubber feet

Pimoroni

Pimoroni PIM556 PICO Omnibus Dual Expander development board

SKU CH-N7QB-70BAP

Connect two Pico Packs or Bases to a single Raspberry Pi Pico with labelled headers and rubber feet included

  • Attach two Pico add-ons simultaneously using dual male header landing areas
  • Prototype with jumper wires or circuitry via extra labelled male GPIO pins
  • Identify connections quickly with clearly labelled female and mirrored male headers
  • Ready to use in minutes as the board arrives 99% assembled with only feet to attach
  • Stable bench setup provided by four included rubber feet

Dual Pico Add-On Expansion Board

The Pimoroni PIM556 PICO Omnibus Dual Expander is a development board that connects two Pico Packs or Bases to a single Raspberry Pi Pico. It arrives fully assembled with labelled headers and rubber feet, so no soldering is required before use.

Makers needing simultaneous add-on access

This board suits developers who want to run two add-ons at once or route extra GPIO signals to jumper wires and prototype circuits. Builders who only ever use one add-on at a time will not need the extra connectors.

Two add-on landing areas with mirrored male headers

The key specification is the pair of mirrored male header zones that accept two add-ons in parallel. If your project requires only a single add-on connection, this dual layout provides no advantage.

Priekšrocības

  • Attach two Pico add-ons simultaneously using dual male header landing areas
  • Prototype with jumper wires or circuitry via extra labelled male GPIO pins
  • Identify connections quickly with clearly labelled female and mirrored male headers
  • Ready to use in minutes as the board arrives 99% assembled with only feet to attach
  • Stable bench setup provided by four included rubber feet

Specifikācijas

Šai precei pagaidām nav publicētu specifikāciju.

Jautājumi par šo preci

What physical space does the PIM556 board need for its rubber feet?

Four adhesive rubber feet are included to stabilise the board on a flat surface; simply peel and stick them to the corners of the underside.

How is the PIM556 connected to a Raspberry Pi Pico, and what step is often missed?

Press the Pico onto the labelled female headers; the board arrives 99% assembled so only the rubber feet need fitting — forgetting the feet is the common oversight.

What ongoing maintenance does the PIM556 require after installation?

No scheduled maintenance is needed; the board has no moving parts or consumables, so it simply remains in place while you swap Pico Packs or jumper wires as required.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.