Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Small black square case fan, 50 by 15 mm, 3-pin Maglev bearing, no LED

Zyvpee

Zyvpee KDE1205PHV2 50x15mm 12V 1.0W 3-pin Maglev case fan

SKU CH-M7PP-NNE9Y

A 50x15mm maglev case fan running at 12V and 1.0W with a 3-pin connector for CPU cooling

  • TypeCase Fan
  • CompatibilityCPU Cooler
  • Bearing TypeMaglev
  • RPM<1600 RPM
  • Power Connector3 Pin
  • ColorBlack
  • Maglev bearing reduces friction and noise
  • 12 V 1.0 W draws minimal power
  • 50 × 15 mm fits tight CPU coolers
  • 3-pin connector enables speed monitoring
  • Under 1600 RPM keeps airflow quiet

Compact 50 mm maglev case fan

The Zyvpee KDE1205PHV2 is a 50 by 15 millimetre case fan designed for tight CPU cooler mounts. It runs on 12 volts and draws 1.0 watt through a standard three-pin connector. The maglev bearing keeps friction low while the black, non-LED frame stays visually neutral inside any build.

Upgrade from sleeve or plain-bearing 5015 fans

This model replaces older 5015 units that develop noise or wear after extended use. The jump is worth it when a cooler’s original fan exceeds 1600 RPM and begins to rattle, or when a silent maglev swap is preferred for a compact heatsink. It fits the same mounting holes without modification.

Fits slim tower and low-profile coolers

The 50 by 15 millimetre footprint slides into narrow fin stacks where larger fans cannot reach. Three-pin voltage control lets the motherboard regulate speed directly, freeing a four-pin header for PWM devices. No LED wiring means one less cable to route in dense small-form-factor chassis.

Priekšrocības

  • Maglev bearing reduces friction and noise
  • 12 V 1.0 W draws minimal power
  • 50 × 15 mm fits tight CPU coolers
  • 3-pin connector enables speed monitoring
  • Under 1600 RPM keeps airflow quiet

Specifikācijas

BrandZyvpee
SeriesKDE1205PHV2
ModelKDE1205PHV2
TypeCase Fan
CompatibilityCPU Cooler
Bearing TypeMaglev
RPM<1600 RPM
Power Connector3 Pin
ColorBlack
LEDNon-LED
FeaturesCPU Cooling
Dimensions50*15MM

Jautājumi par šo preci

Will the 50 x 15 mm frame fit my CPU cooler mounting holes?

The fan measures 50 mm per side and 15 mm thick, matching the standard 5015 footprint used on many low-profile CPU coolers.

How do I connect the 3-pin lead so the motherboard reads speed correctly?

Align the three wires with the board’s 3-pin header — ground, 12 V, and tach — so the RPM signal reports up to 1600 RPM.

When should I expect the maglev bearing to need replacement?

Maglev bearings run without contact, so they typically last for years of continuous 12 V 1.0 W operation before any service is required.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.