Aceitamos criptomoeda — para que as moedas que detém possam comprar material informático real.Pague em cripto, gaste-a em material informático real. Envio seguro gratuito para todo o mundo acima de 399 $. Caixas neutras, sem marca, expedidas a partir da Alemanha.Envio seguro gratuito acima de 399 $. A sua taxa fica bloqueada durante 30 minutos assim que abre a finalização da compra.Taxa bloqueada 30 minutos. Cada artigo é selado, o seu número de série é verificado, e está coberto por uma garantia de 24 meses.Selado, garantido 24 meses.

Artigos guardados Iniciar sessão
Small black square case fan, 50 by 15 mm, 3-pin Maglev bearing, no LED

Zyvpee

Zyvpee KDE1205PHV2 50x15mm 12V 1.0W 3-pin Maglev case fan

SKU CH-M7PP-NNE9Y

A 50x15mm maglev case fan running at 12V and 1.0W with a 3-pin connector for CPU cooling

  • TypeCase Fan
  • CompatibilityCPU Cooler
  • Bearing TypeMaglev
  • RPM<1600 RPM
  • Power Connector3 Pin
  • ColorBlack
  • Maglev bearing reduces friction and noise
  • 12 V 1.0 W draws minimal power
  • 50 × 15 mm fits tight CPU coolers
  • 3-pin connector enables speed monitoring
  • Under 1600 RPM keeps airflow quiet

Compact 50 mm maglev case fan

The Zyvpee KDE1205PHV2 is a 50 by 15 millimetre case fan designed for tight CPU cooler mounts. It runs on 12 volts and draws 1.0 watt through a standard three-pin connector. The maglev bearing keeps friction low while the black, non-LED frame stays visually neutral inside any build.

Upgrade from sleeve or plain-bearing 5015 fans

This model replaces older 5015 units that develop noise or wear after extended use. The jump is worth it when a cooler’s original fan exceeds 1600 RPM and begins to rattle, or when a silent maglev swap is preferred for a compact heatsink. It fits the same mounting holes without modification.

Fits slim tower and low-profile coolers

The 50 by 15 millimetre footprint slides into narrow fin stacks where larger fans cannot reach. Three-pin voltage control lets the motherboard regulate speed directly, freeing a four-pin header for PWM devices. No LED wiring means one less cable to route in dense small-form-factor chassis.

Pontos fortes

  • Maglev bearing reduces friction and noise
  • 12 V 1.0 W draws minimal power
  • 50 × 15 mm fits tight CPU coolers
  • 3-pin connector enables speed monitoring
  • Under 1600 RPM keeps airflow quiet

Especificações

BrandZyvpee
SeriesKDE1205PHV2
ModelKDE1205PHV2
TypeCase Fan
CompatibilityCPU Cooler
Bearing TypeMaglev
RPM<1600 RPM
Power Connector3 Pin
ColorBlack
LEDNon-LED
FeaturesCPU Cooling
Dimensions50*15MM

Perguntas sobre este artigo

Will the 50 x 15 mm frame fit my CPU cooler mounting holes?

The fan measures 50 mm per side and 15 mm thick, matching the standard 5015 footprint used on many low-profile CPU coolers.

How do I connect the 3-pin lead so the motherboard reads speed correctly?

Align the three wires with the board’s 3-pin header — ground, 12 V, and tach — so the RPM signal reports up to 1600 RPM.

When should I expect the maglev bearing to need replacement?

Maglev bearings run without contact, so they typically last for years of continuous 12 V 1.0 W operation before any service is required.

Também nesta secção

Os clientes também compararam

Mesma prateleira, mesma finalização da compra — oito moedas e uma taxa bloqueada durante 30 minutos.