Acceptăm criptomonede — astfel, criptomonedele pe care le dețineți pot cumpăra echipamente reale.Plătiți în cripto, cheltuiți-o pe echipamente reale. Livrare asigurată gratuită oriunde în lume peste 399 $. Cartoane neutre, fără marcă, expediate din Germania.Livrare asigurată gratuită peste 399 $. Cursul dumneavoastră este blocat timp de 30 de minute de la deschiderea paginii de plată.Curs blocat 30 de minute. Fiecare articol este sigilat, numărul de serie este verificat, iar produsul este acoperit de o garanție de 24 de luni.Sigilat, garantat 24 de luni.

Produse urmărite Conectare
Small black square case fan, 50 by 15 mm, 3-pin Maglev bearing, no LED

Zyvpee

Zyvpee KDE1205PHV2 50x15mm 12V 1.0W 3-pin Maglev case fan

SKU CH-M7PP-NNE9Y

A 50x15mm maglev case fan running at 12V and 1.0W with a 3-pin connector for CPU cooling

  • TypeCase Fan
  • CompatibilityCPU Cooler
  • Bearing TypeMaglev
  • RPM<1600 RPM
  • Power Connector3 Pin
  • ColorBlack
  • Maglev bearing reduces friction and noise
  • 12 V 1.0 W draws minimal power
  • 50 × 15 mm fits tight CPU coolers
  • 3-pin connector enables speed monitoring
  • Under 1600 RPM keeps airflow quiet

Compact 50 mm maglev case fan

The Zyvpee KDE1205PHV2 is a 50 by 15 millimetre case fan designed for tight CPU cooler mounts. It runs on 12 volts and draws 1.0 watt through a standard three-pin connector. The maglev bearing keeps friction low while the black, non-LED frame stays visually neutral inside any build.

Upgrade from sleeve or plain-bearing 5015 fans

This model replaces older 5015 units that develop noise or wear after extended use. The jump is worth it when a cooler’s original fan exceeds 1600 RPM and begins to rattle, or when a silent maglev swap is preferred for a compact heatsink. It fits the same mounting holes without modification.

Fits slim tower and low-profile coolers

The 50 by 15 millimetre footprint slides into narrow fin stacks where larger fans cannot reach. Three-pin voltage control lets the motherboard regulate speed directly, freeing a four-pin header for PWM devices. No LED wiring means one less cable to route in dense small-form-factor chassis.

Puncte forte

  • Maglev bearing reduces friction and noise
  • 12 V 1.0 W draws minimal power
  • 50 × 15 mm fits tight CPU coolers
  • 3-pin connector enables speed monitoring
  • Under 1600 RPM keeps airflow quiet

Specificații

BrandZyvpee
SeriesKDE1205PHV2
ModelKDE1205PHV2
TypeCase Fan
CompatibilityCPU Cooler
Bearing TypeMaglev
RPM<1600 RPM
Power Connector3 Pin
ColorBlack
LEDNon-LED
FeaturesCPU Cooling
Dimensions50*15MM

Întrebări despre acest articol

Will the 50 x 15 mm frame fit my CPU cooler mounting holes?

The fan measures 50 mm per side and 15 mm thick, matching the standard 5015 footprint used on many low-profile CPU coolers.

How do I connect the 3-pin lead so the motherboard reads speed correctly?

Align the three wires with the board’s 3-pin header — ground, 12 V, and tach — so the RPM signal reports up to 1600 RPM.

When should I expect the maglev bearing to need replacement?

Maglev bearings run without contact, so they typically last for years of continuous 12 V 1.0 W operation before any service is required.

Tot din acest raion

Clienții au comparat și acestea.

Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.