Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Small black 45mm CPU fan with maglev bearing and 3-pin connector

Zyvpee

Zyvpee KDE1245PFV1 45mm 12V 1.7W 3-pin CPU cooler

SKU CH-FGST-23HTQ

45 mm maglev CPU cooler fan runs on 12 V and draws 1.7 W through a 3-pin connector

  • TypeCPU Cooler Fan
  • Bearing TypeMaglev
  • Power Connector3 Pin
  • ColorBlack
  • LEDNon-LED
  • Featurescpu fan
  • Compact 45mm footprint fits tight builds
  • Maglev bearing reduces friction for quiet operation
  • Low 1.7W draw keeps power consumption minimal
  • 12V 3-pin connector enables straightforward motherboard control
  • Black non-LED design suits understated system aesthetics

Compact 45 mm CPU fan

The Zyvpee KDE1245PFV1 is a 45 mm square frame cooler that runs on 12 V and draws 1.7 W through a 3-pin connector. It fits small-form-factor builds where a low-profile fan is required. The maglev bearing reduces friction for quieter operation at idle. Builders replacing a failed OEM cooler in thin clients or embedded boards will find the dimensions match common 45 mm mounting patterns.

Steady thermal behaviour

At the rated 1.7 W the motor maintains constant speed without the voltage sag seen in higher-draw fans. Maglev suspension keeps acoustic output stable during long sessions because there is no sleeve wear to increase noise over time. The 3-pin header reports speed to the motherboard so fan curves respond to actual load. Sustained airflow remains predictable in enclosures with restricted intake paths.

Straightforward drop-in install

Four corner holes align with standard 45 mm brackets so no adapter plate is needed. The three-wire lead plugs directly into a CPU_FAN header; polarity follows the usual ground-sense-power order. Builders sometimes route the short cable under a motherboard heatsink and strain the connector — leave slack before securing screws. Verify the 10 mm thickness clears nearby capacitors before tightening.

Priekšrocības

  • Compact 45mm footprint fits tight builds
  • Maglev bearing reduces friction for quiet operation
  • Low 1.7W draw keeps power consumption minimal
  • 12V 3-pin connector enables straightforward motherboard control
  • Black non-LED design suits understated system aesthetics

Specifikācijas

BrandZyvpee
SeriesKDE1245
ModelKDE1245PFV1
TypeCPU Cooler Fan
Bearing TypeMaglev
Power Connector3 Pin
ColorBlack
LEDNon-LED
Featurescpu fan
Dimensions45 * 10mm
Package Contentsrefer to title

Jautājumi par šo preci

How much power does the 12V 1.7W fan draw during continuous operation?

The fan is rated at 1.7W on a 12V supply, giving a low steady-state power draw suitable for small-form-factor builds.

Does the 3-pin connector work directly with a standard motherboard CPU fan header?

Yes, the 3-pin connector fits a typical 4-pin CPU fan header; speed is controlled by voltage regulation from the board.

Will the 45mm height and Maglev bearing clear low-profile heatsinks used on older platforms?

At 45mm tall the fan suits slim coolers, and the Maglev bearing reduces friction for reliable long-term spinning in tight clearances.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.