Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Small black 45mm CPU fan with maglev bearing and 3-pin connector

Zyvpee

Zyvpee KDE1245PFV1 45mm 12V 1.7W 3-pin CPU cooler

SKU CH-FGST-23HTQ

45 mm maglev CPU cooler fan runs on 12 V and draws 1.7 W through a 3-pin connector

  • TypeCPU Cooler Fan
  • Bearing TypeMaglev
  • Power Connector3 Pin
  • ColorBlack
  • LEDNon-LED
  • Featurescpu fan
  • Compact 45mm footprint fits tight builds
  • Maglev bearing reduces friction for quiet operation
  • Low 1.7W draw keeps power consumption minimal
  • 12V 3-pin connector enables straightforward motherboard control
  • Black non-LED design suits understated system aesthetics

Compact 45 mm CPU fan

The Zyvpee KDE1245PFV1 is a 45 mm square frame cooler that runs on 12 V and draws 1.7 W through a 3-pin connector. It fits small-form-factor builds where a low-profile fan is required. The maglev bearing reduces friction for quieter operation at idle. Builders replacing a failed OEM cooler in thin clients or embedded boards will find the dimensions match common 45 mm mounting patterns.

Steady thermal behaviour

At the rated 1.7 W the motor maintains constant speed without the voltage sag seen in higher-draw fans. Maglev suspension keeps acoustic output stable during long sessions because there is no sleeve wear to increase noise over time. The 3-pin header reports speed to the motherboard so fan curves respond to actual load. Sustained airflow remains predictable in enclosures with restricted intake paths.

Straightforward drop-in install

Four corner holes align with standard 45 mm brackets so no adapter plate is needed. The three-wire lead plugs directly into a CPU_FAN header; polarity follows the usual ground-sense-power order. Builders sometimes route the short cable under a motherboard heatsink and strain the connector — leave slack before securing screws. Verify the 10 mm thickness clears nearby capacitors before tightening.

Kohokohdat

  • Compact 45mm footprint fits tight builds
  • Maglev bearing reduces friction for quiet operation
  • Low 1.7W draw keeps power consumption minimal
  • 12V 3-pin connector enables straightforward motherboard control
  • Black non-LED design suits understated system aesthetics

Tekniset tiedot

BrandZyvpee
SeriesKDE1245
ModelKDE1245PFV1
TypeCPU Cooler Fan
Bearing TypeMaglev
Power Connector3 Pin
ColorBlack
LEDNon-LED
Featurescpu fan
Dimensions45 * 10mm
Package Contentsrefer to title

Kysymyksiä tästä tuotteesta

How much power does the 12V 1.7W fan draw during continuous operation?

The fan is rated at 1.7W on a 12V supply, giving a low steady-state power draw suitable for small-form-factor builds.

Does the 3-pin connector work directly with a standard motherboard CPU fan header?

Yes, the 3-pin connector fits a typical 4-pin CPU fan header; speed is controlled by voltage regulation from the board.

Will the 45mm height and Maglev bearing clear low-profile heatsinks used on older platforms?

At 45mm tall the fan suits slim coolers, and the Maglev bearing reduces friction for reliable long-term spinning in tight clearances.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.