Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Small black 45mm CPU fan with maglev bearing and 3-pin connector

Zyvpee

Zyvpee KDE1245PFV1 45mm 12V 1.7W 3-pin CPU cooler

SKU CH-FGST-23HTQ

45 mm maglev CPU cooler fan runs on 12 V and draws 1.7 W through a 3-pin connector

  • TypeCPU Cooler Fan
  • Bearing TypeMaglev
  • Power Connector3 Pin
  • ColorBlack
  • LEDNon-LED
  • Featurescpu fan
  • Compact 45mm footprint fits tight builds
  • Maglev bearing reduces friction for quiet operation
  • Low 1.7W draw keeps power consumption minimal
  • 12V 3-pin connector enables straightforward motherboard control
  • Black non-LED design suits understated system aesthetics

Compact 45 mm CPU fan

The Zyvpee KDE1245PFV1 is a 45 mm square frame cooler that runs on 12 V and draws 1.7 W through a 3-pin connector. It fits small-form-factor builds where a low-profile fan is required. The maglev bearing reduces friction for quieter operation at idle. Builders replacing a failed OEM cooler in thin clients or embedded boards will find the dimensions match common 45 mm mounting patterns.

Steady thermal behaviour

At the rated 1.7 W the motor maintains constant speed without the voltage sag seen in higher-draw fans. Maglev suspension keeps acoustic output stable during long sessions because there is no sleeve wear to increase noise over time. The 3-pin header reports speed to the motherboard so fan curves respond to actual load. Sustained airflow remains predictable in enclosures with restricted intake paths.

Straightforward drop-in install

Four corner holes align with standard 45 mm brackets so no adapter plate is needed. The three-wire lead plugs directly into a CPU_FAN header; polarity follows the usual ground-sense-power order. Builders sometimes route the short cable under a motherboard heatsink and strain the connector — leave slack before securing screws. Verify the 10 mm thickness clears nearby capacitors before tightening.

Najważniejsze cechy

  • Compact 45mm footprint fits tight builds
  • Maglev bearing reduces friction for quiet operation
  • Low 1.7W draw keeps power consumption minimal
  • 12V 3-pin connector enables straightforward motherboard control
  • Black non-LED design suits understated system aesthetics

Specyfikacja

BrandZyvpee
SeriesKDE1245
ModelKDE1245PFV1
TypeCPU Cooler Fan
Bearing TypeMaglev
Power Connector3 Pin
ColorBlack
LEDNon-LED
Featurescpu fan
Dimensions45 * 10mm
Package Contentsrefer to title

Pytania dotyczące tego produktu

How much power does the 12V 1.7W fan draw during continuous operation?

The fan is rated at 1.7W on a 12V supply, giving a low steady-state power draw suitable for small-form-factor builds.

Does the 3-pin connector work directly with a standard motherboard CPU fan header?

Yes, the 3-pin connector fits a typical 4-pin CPU fan header; speed is controlled by voltage regulation from the board.

Will the 45mm height and Maglev bearing clear low-profile heatsinks used on older platforms?

At 45mm tall the fan suits slim coolers, and the Maglev bearing reduces friction for reliable long-term spinning in tight clearances.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.