Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Green rectangular DDR3 DIMM module with black chips and gold contacts

A-Tech

A-Tech 8GB DDR3 1600 ECC RDIMM 2Rx8 Server Memory

SKU CH-GBRF-0GF73

8GB DDR3 1600 ECC registered DIMM with CL11 latency and 1.5V operation

  • Capacity8GB
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.50V
  • ECCYes
  • Buffered/RegisteredRegistered
  • ECC protection prevents data errors in server workloads
  • Registered design stabilises signal integrity on multi-module configurations
  • 1600 MHz DDR3 speed matches PC3-12800 system requirements
  • 50 V standard voltage ensures broad platform compatibility
  • 240-pin DIMM form factor fits DDR3 server memory slots

8GB DDR3 1600 ECC Registered DIMM

This 8GB A-Tech module runs at DDR3 1600 (PC3-12800) with CL11 latency and 1.50V operation. It is a registered ECC DIMM built with a 2Rx8 organisation using major-brand chips. The 240-pin form factor fits server and workstation boards that require registered memory.

Suits servers needing registered ECC DDR3

Administrators upgrading or repairing systems that specify registered ECC DDR3 at 1600 MHz will find this module a direct replacement for Hynix HMT41GV7BFR8C-PB and HMT41GV7MFR8C-PB. Builders whose platforms only accept unbuffered memory or a different DDR generation cannot use this part.

Registered ECC with 2Rx8 organisation

The registered buffer and ECC function are mandatory for the target platform; the module will not operate in systems that require unbuffered non-ECC memory. Verify that your board supports registered DDR3 DIMMs before ordering.

Høydepunkter

  • ECC protection prevents data errors in server workloads
  • Registered design stabilises signal integrity on multi-module configurations
  • 1600 MHz DDR3 speed matches PC3-12800 system requirements
  • 50 V standard voltage ensures broad platform compatibility
  • 240-pin DIMM form factor fits DDR3 server memory slots

Spesifikasjoner

BrandA-Tech
SeriesCompatible Replacement for Hynix
ModelHMT41GV7BFR8C-PB, HMT41GV7MFR8C-PB
Capacity8GB
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.50V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx8
ChipsetMajor Brand Chipset
FeaturesHMT41GV7BFR8C-PB, HMT41GV7MFR8C-PB

Spørsmål om denne varen

Will the 240-pin DDR3 DIMM fit my server's registered memory slots?

Yes, this module uses the standard 240-pin DDR3 DIMM form factor required for registered ECC server memory slots.

What is the correct way to seat the registered DIMM so the ECC function initialises?

Align the notch with the slot key, press firmly straight down until both side clips click shut; the register chip adds height so use even pressure on both ends.

How can I tell when the 8GB 2Rx8 module should be replaced?

Run a full memory test at each boot; replace the stick if the BIOS logs corrected ECC errors or the OS reports hardware memory failures.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.