Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Compact rectangular ASIC miner in matte grey metal with front grille, rear dual 6-pin power ports and Goldshell branding

Goldshell

Goldshell Mini Doge 3 700M/550M Dual Mode mining hardware

SKU CH-0732-83JC3

A dual-mode ASIC miner for Dogecoin and Litecoin delivering 700 Mh/s at 400 W or 550 Mh/s at 260 W

  • Dual-mode ASIC delivers 700Mh/s at 400W for strong Dogecoin and Litecoin earnings
  • Low-power mode runs at 550Mh/s using only 260W to cut electricity costs
  • Compact bare-bone chassis fits tight spaces without extra rack hardware
  • Two mandatory 6-pin power inputs ensure stable current delivery under full load
  • Purpose-built for Scrypt coins so no algorithm switching or firmware hassles

Dual-mode Scrypt ASIC for LTC and DOGE

The Goldshell Mini Doge 3 is an ASIC miner built for the Scrypt algorithm used by Litecoin and Dogecoin. It targets hobbyist and small-scale operators who want a compact unit that can run at two distinct performance points without changing hardware.

High and low power profiles replace single-speed

The default profile delivers 700Mh/s at 400W while the low-power profile drops to 550Mh/s at 260W. Switching between them lets the operator match electricity cost or thermal headroom without buying a second device, making the jump worthwhile when power rates vary by time of day or season.

Two 6-pin power inputs set the hard wiring limit

Both 6-pin connectors must be fully seated before the miner is powered on; running on a single connector is not supported. This dual-connector requirement defines the minimum cabling and power-supply layout the builder must provide.

Høydepunkter

  • Dual-mode ASIC delivers 700Mh/s at 400W for strong Dogecoin and Litecoin earnings
  • Low-power mode runs at 550Mh/s using only 260W to cut electricity costs
  • Compact bare-bone chassis fits tight spaces without extra rack hardware
  • Two mandatory 6-pin power inputs ensure stable current delivery under full load
  • Purpose-built for Scrypt coins so no algorithm switching or firmware hassles

Spesifikasjoner

Ingen publiserte spesifikasjoner for denne varen ennå.

Spørsmål om denne varen

What are the power connector requirements for the Goldshell Mini Doge 3?

The miner requires two 6PIN power interfaces to be fully connected. Operating with only one 6PIN plugged in is not supported and must be avoided.

What is the correct installation step for the dual 6PIN power interfaces on this miner?

Before powering on, verify that both 6PIN connectors are completely seated. The unit will not operate correctly if only a single 6PIN interface is used.

Which components on the Goldshell Mini Doge 3 are most likely to need replacement over time?

The internal cooling fans are the primary moving parts and will typically require replacement after extended continuous operation at 400W or 260W power draw.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.