Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Flat 20 cm PCIe 3.0 x16 riser cable with 90 degree connector and power LED

myVolts

myVolts PCIe 3.0 x16 Riser Cable 20cm 90° Power LED

SKU CH-JV6R-JCGPQ

A 20 cm PCIe 3.0 x16 riser cable with a 90° connector and 3.3 V/12 V power LED for vertical GPU mounting

  • TypeAT
  • Fully flexible six-wire construction routes through tight gaps
  • EMI shielded with TPE sleeve and PE insulation for stable signals
  • Gold-plated contacts rated at 3U thickness extend plug-in life
  • 20 cm length with 90-degree connector suits vertical GPU mounts
  • On-board 3.3V and 12V power LEDs confirm rail status

PCIe 3.0 x16 riser cable, 20 cm, 90°

This PCIe 3.0 x16 riser cable extends a graphics card by 20 cm and bends 90 degrees for vertical mounting. Six-wire banded construction gives full flexibility to route through tight gaps. Pure copper tinned cores with TPE and PE shielding deliver high-frequency, low-attenuation signals. Gold-plated fingers rated at 3U improve durability and electrical contact.

Builders fitting a GPU vertically in a compact case

Suits builders who need a short, angled extender to position a graphics card upright in a small chassis. The flexible six-wire design eases routing around motherboard components and drive cages. Not for users who require a longer reach beyond 20 cm or a straight connector for horizontal layouts.

20 cm length with 90-degree connector

The cable measures 20 cm and terminates in a 90-degree PCIe x16 plug, fixing the mounting geometry for vertical GPU installs. EMI shielding uses a TPE sleeve and PE insulation with 28/30 AWG tinned copper conductors. A 3.3 V / 12 V power LED indicates live rails on the riser board.

Høydepunkter

  • Fully flexible six-wire construction routes through tight gaps
  • EMI shielded with TPE sleeve and PE insulation for stable signals
  • Gold-plated contacts rated at 3U thickness extend plug-in life
  • 20 cm length with 90-degree connector suits vertical GPU mounts
  • On-board 3.3V and 12V power LEDs confirm rail status

Spesifikasjoner

TypeAT

Spørsmål om denne varen

What motherboard slot is required for this PCIe 3.0 x16 riser cable?

The cable plugs into a PCIe 3.0 x16 slot on the motherboard and extends the connection to the graphics card.

Will this 20 cm riser cable work with a graphics card that only supports PCIe 2.0?

PCIe 3.0 is backward compatible, so the riser will carry PCIe 2.0 signals at PCIe 2.0 speeds.

How can I verify the 3.3 V and 12 V power LEDs are lit after installing the cable?

Both LEDs should glow steadily once the system powers on, confirming the riser is delivering auxiliary power to the card.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.