Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn

OWC

OWC 16GB (2x8GB) DDR3L 1333 ECC RDIMM Cisco UCS B200 M1 C200 M1

SKU CH-G1XA-K9D3W

A 16 GB dual-module DDR3L 1333 ECC registered RDIMM kit for Cisco UCS B200 M1 and C200 M1 servers

  • Capacity16GB (2 x 8GB)
  • Type240-Pin DDR3L ECC RDIMM
  • SpeedDDR3L 1333 (PC3L 10600)
  • CAS LatencyCL9
  • Voltage1.35V
  • ECCYes

Capacity 16GB (2 x 8GB)

  • ECC registered design protects data integrity in servers
  • 16 GB kit (2 × 8 GB) expands Cisco UCS capacity
  • DDR3L 1333 MHz CL9 matches system specification
  • 35 V low voltage reduces power draw
  • Validated replacement for Cisco part numbers N01M308GB2, UCSMR1X082RXA, UCSMR2X082RXB, UCSMR2X082RXC

Targeted Server Upgrade

This OWC kit delivers 16 GB of DDR3L 1333 ECC registered memory in a matched pair of 8 GB modules. It is built for Cisco UCS B200 M1 and C200 M1 servers that require 240-pin RDIMMs with CL9 timing and 1.35 V operation. The registered design and 2Rx4 organisation ensure signal integrity in multi-DIMM configurations.

Replaces Cisco OEM Parts

The kit directly replaces Cisco part numbers N01M308GB2, UCSMR1X082RXA, UCSMR2X082RXB and UCSMR2X082RXC. It is the correct choice when a service tag or memory configurator calls for PC3L-10600 registered ECC modules. The jump is worth it when the existing slots are populated with smaller RDIMMs or when a failed OEM stick must be swapped for a validated equivalent.

Capacity and Headroom

Two 8 GB modules fill a dual-channel pair, giving 16 GB of error-correcting capacity for virtualisation hosts, database tiers or NAS workloads. The registered buffer allows further expansion up to the platform’s slot limit without electrical loading issues. It runs out when the application demands exceed the 1333 MT/s bus or when the server’s maximum supported density per socket is reached.

Høydepunkter

  • ECC registered design protects data integrity in servers
  • 16 GB kit (2 × 8 GB) expands Cisco UCS capacity
  • DDR3L 1333 MHz CL9 matches system specification
  • 35 V low voltage reduces power draw
  • Validated replacement for Cisco part numbers N01M308GB2, UCSMR1X082RXA, UCSMR2X082RXB, UCSMR2X082RXC

Spesifikasjoner

BrandOWC
Part Number1R3T32R4016P
Capacity16GB (2 x 8GB)
Type240-Pin DDR3L ECC RDIMM
SpeedDDR3L 1333 (PC3L 10600)
CAS LatencyCL9
Voltage1.35V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx4
Heat SpreaderNo
Compatible SystemCisco UCS B200 M1
Cisco UCS C200 M1

Andre versjoner av denne modellen

5 flere i samme serie

Samme familie, annet minne, annen kjøler eller klokkefrekvens — sammenlign før du bestemmer deg.

Spørsmål om denne varen

Will the 240-pin DDR3L RDIMM modules fit the memory slots in my Cisco UCS B200 M1 or C200 M1 server?

Yes, the kit uses the 240-pin DDR3L RDIMM form factor specified for the Cisco UCS B200 M1 and C200 M1, so the modules seat directly in the server's DIMM slots.

What is the correct installation sequence for the two 8 GB registered DIMMs, and what step is commonly missed?

Install the modules in the slot order defined by the Cisco UCS B200 M1 or C200 M1 memory population guide, and ensure each registered DIMM clicks fully into place so the ECC registered buffer initialises correctly.

When should I expect to replace these DDR3L 1333 ECC registered modules in a Cisco UCS server?

Replace them only if a module fails or if you upgrade the Cisco UCS B200 M1 or C200 M1 to a platform that requires a different memory generation or capacity.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.