Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Green circuit board with black memory chips and gold edge connector

OWC

OWC 2U1D42R816GB 16GB DDR4 2133 CL15 1.2V 288pin UDIMM HP Envy Phoenix 860

SKU CH-P50J-JEZH7

16 GB DDR4 2133 CL15 UDIMM adds memory to HP Envy Phoenix 860 desktops

  • Capacity16GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2133 (PC4 17000)
  • CAS LatencyCL15
  • Voltage1.2V
  • ECCNo
  • 16GB DDR4 2133MHz CL15 boosts HP Envy Phoenix 860 responsiveness
  • JEDEC and RoHS compliant for a warranty-safe memory upgrade
  • 2V low-voltage operation reduces system power draw
  • Unbuffered 288-pin UDIMM installs easily in compatible 860-series desktops
  • 2Rx8 dual-rank design supports multitasking with larger files

16GB DDR4 UDIMM for HP Envy Phoenix 860

This 16GB DDR4 2133MHz CL15 module is built for HP Envy Phoenix 860 desktops including the 860-009nf, 860-010, 860-010ng, 860-011NF and 860-011no models. It suits owners who need a direct-fit memory upgrade without guessing compatibility. Buyers with other platforms or laptops cannot use this 288-pin desktop DIMM.

2133MHz CL15 JEDEC specification

The module runs at the standard DDR4 2133 (PC4-17000) speed with CL15 latency at 1.2V, matching the JEDEC baseline for this system. It is a non-ECC, unbuffered, dual-rank 2Rx8 stick, so it will not work in servers or workstations that require registered or error-correcting memory.

Simple DIY installation

Installation is a straightforward DIY task: power down, open the case, seat the DIMM in an empty slot until the clips click, then reboot. The most common issue is the system not recognising the new capacity because the module is not fully seated or the BIOS needs a reset. No heat spreader is fitted, so clearance is not a concern.

Høydepunkter

  • 16GB DDR4 2133MHz CL15 boosts HP Envy Phoenix 860 responsiveness
  • JEDEC and RoHS compliant for a warranty-safe memory upgrade
  • 2V low-voltage operation reduces system power draw
  • Unbuffered 288-pin UDIMM installs easily in compatible 860-series desktops
  • 2Rx8 dual-rank design supports multitasking with larger files

Spesifikasjoner

BrandOWC
Part Number2U1D42R816GB
Capacity16GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2133 (PC4 17000)
CAS LatencyCL15
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
Heat SpreaderNo
Compatible SystemHP ENVY Phoenix 860-009nf
HP ENVY Phoenix 860-010
HP ENVY Phoenix 860-010ng
HP ENVY Phoenix 860-011NF
HP ENVY Phoenix 860-011no

Andre versjoner av denne modellen

5 flere i samme serie

Samme familie, annet minne, annen kjøler eller klokkefrekvens — sammenlign før du bestemmer deg.

Spørsmål om denne varen

Will the 2133 MHz speed run at that rate in my HP Envy Phoenix 860?

The module is rated DDR4 2133 (PC4-17000) and will operate at that frequency if the system supports it; otherwise it downclocks to the highest speed the platform allows.

Does the PC4-17000 label limit the bandwidth I can actually use?

PC4-17000 marks a peak transfer rate of 17 GB/s; real-world throughput is lower and also depends on the memory controller in the HP Envy Phoenix 860.

Will this 288-pin UDIMM fit the slots in an HP Envy Phoenix 860?

Yes — it is a standard 288-pin DDR4 UDIMM designed for the HP Envy Phoenix 860 series listed in the compatibility data.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.