Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Brass extension coupler, male to female G 1/4 inch, knurled finish

PrimoChill

PrimoChill G 1/4in 7.5mm SX Extension Coupler diy cooling

SKU CH-ZZGX-10RP7

Male-to-female G 1/4in extension adds 7.5mm height for fitting clearance in custom loops

  • TypeCPU Block

GroupWaterCoolingOption UV Pink

Vis 9 flere konfigurasjoner

Overstrøkne versjoner finnes, men er ikke på lager her.

  • Adds 7.5mm clearance with low-profile G 1/4in extension
  • Male-to-female thread connects any standard G 1/4in fitting
  • Coated brass body resists corrosion in custom loops
  • Pre-installed sealing ring on male side prevents leaks
  • 5mm total height keeps builds compact

Extension Coupler for Custom Loops

This PrimoChill G 1/4in coupler adds 7.5mm of reach between a component and a fitting. It solves clearance problems in tight custom water-cooling builds where a standard fitting sits too close to a block, radiator or reservoir. The male-to-female design threads directly into any G 1/4in port without adapters.

Passive Brass Construction

Coated brass material adds no active heat, noise or power draw to the loop. The coupler simply extends the fluid path while the installed sealing ring on the male side maintains a leak-free joint. Thermal performance and acoustic profile remain entirely dependent on the surrounding components.

Sealing Ring Included

One sealing ring comes pre-installed on the male thread so the joint is ready to tighten. No extra washers, O-rings or thread tape are bundled. The 20-year-old US brand notes that Candy SX finish tones can vary between knurled and smooth surfaces, which is a cosmetic consideration only.

Høydepunkter

  • Adds 7.5mm clearance with low-profile G 1/4in extension
  • Male-to-female thread connects any standard G 1/4in fitting
  • Coated brass body resists corrosion in custom loops
  • Pre-installed sealing ring on male side prevents leaks
  • 5mm total height keeps builds compact

Spesifikasjoner

TypeCPU Block

Andre versjoner av denne modellen

5 flere i samme serie

Samme familie, annet minne, annen kjøler eller klokkefrekvens — sammenlign før du bestemmer deg.

Spørsmål om denne varen

How do I install the PrimoChill G 1/4in 7.5mm SX Extension Coupler and what step is often missed?

Thread the male side into the component until the sealing ring contacts the surface, then tighten the female fitting onto the exposed male thread. The step often missed is verifying the ring is seated flush before final torque.

What maintenance or replacement will the PrimoChill G 1/4in 7.5mm SX Extension Coupler need later?

The coated brass body is maintenance-free, but the installed sealing ring on the male thread should be inspected during loop service and replaced if it shows compression set or cracking.

What limit appears first on the PrimoChill G 1/4in 7.5mm SX Extension Coupler under sustained use?

The 7.5 mm solid height adds fixed stack length; in tight builds the combined 12.5 mm installed height can contact adjacent components before thermal or pressure limits are reached.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.