Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Green rectangular circuit board with black connectors and silver components

WaveShare

WaveShare BIGTREETECH Manta M8P V1.0 32Bit development board

SKU CH-6X6E-QVE04

32-bit ARM Cortex-M0+ board runs Klipper with 64 MHz STM32G0B1VET6 and supports TMC5160, TMC2209, TMC2130 drivers

  • CPU TypeOther
  • 32-bit ARM Cortex-M0+ core at 64 MHz delivers responsive real-time control
  • TPS5450 power stage accepts 12 V or 24 V input and supplies up to 5 A continuous for Raspberry Pi
  • BTB connector lets you swap core boards such as CB1 without soldering
  • Jumper-selectable pull-up enables direct PT1000 thermistor use without extra modules
  • Three four-wire fan headers support water-cooling and active airflow setups

32-bit ARM development board for Klipper printers

The BIGTREETECH Manta M8P V1.0 is a 32-bit control board built around an STM32G0B1VET6 Cortex-M0+ MCU running at 64 MHz. It targets makers and 3D-printer builders who run Klipper firmware and want an integrated motherboard that pairs with a CB1 V2.2 core board. High-performance MOSFETs keep heat low during extended prints.

BTB core-board connector and flexible power input

A board-to-board connector lets the mainboard accept core boards beyond the CM4 form factor, so users can swap in a BIGTREETECH CB1 or compatible module. The onboard TPS5450 regulator handles 12 V or 24 V DC input and delivers up to 5 A continuous with a 6 A peak, enough to power a Raspberry Pi alongside the printer electronics. A three-way four-wire fan header supports water-cooling devices, and jumper-selectable thermistor pull-ups allow PT1000 sensors without extra modules.

STM32G0B1VET6 MCU at 64 MHz decides firmware fit

The Cortex-M0+ core at 64 MHz sets the processing ceiling for Klipper’s real-time motion tasks. Builders needing higher step rates or more concurrent axes should verify this MCU meets their performance envelope before committing. Firmware upgrades are handled via SD card or DFU through Klipper’s make flash command, and the board reserves an SPI expansion for an external accelerometer.

Høydepunkter

  • 32-bit ARM Cortex-M0+ core at 64 MHz delivers responsive real-time control
  • TPS5450 power stage accepts 12 V or 24 V input and supplies up to 5 A continuous for Raspberry Pi
  • BTB connector lets you swap core boards such as CB1 without soldering
  • Jumper-selectable pull-up enables direct PT1000 thermistor use without extra modules
  • Three four-wire fan headers support water-cooling and active airflow setups

Spesifikasjoner

CPU TypeOther

Spørsmål om denne varen

Does the board run on 12 V or 24 V DC?

The TPS5450 power chip accepts 12 V or 24 V DC input and delivers up to 5 A continuous, 6 A peak.

What mounting or connector space does the BTB link need?

A board-to-board connector joins the control board to the CB1 V2.2 core board; allow clearance for that vertical stack.

How do I flash firmware and what step is often missed?

Flash via SD card or DFU with Klipper's make flash command; the jumper for thermistor pull-up must be set before flashing.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.