BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
$214,99
0.0027877BTC
Stokta
A-Tech
A-Tech 16GB DDR5 5600MHz ECC UDIMM 1Rx8 for Hynix HMCG78AGBEA HMCG78AGBEA081N Server RAM
16 GB DDR5 5600 ECC UDIMM for servers needing error-correcting memory at standard voltage
- Capacity16GB
- Type288-Pin DDR5 SDRAM
- SpeedDDR5 5600 (PC5 44800)
- CAS Latency40
- Voltage1.10V
- ECCYes
- ECC protection guards data integrity with built-in error correction
- DDR5 5600 MHz speed accelerates demanding server workloads
- 16 GB capacity expands memory headroom for virtualization
- 1 V standard voltage reduces power draw per module
- 288-pin UDIMM form factor fits compatible DDR5 server boards
16GB DDR5-5600 ECC UDIMM for Hynix replacement
This 16GB DDR5 module runs at 5600MHz with CAS latency 40 and 1.10V operation. It is built as an unbuffered ECC UDIMM with a 1Rx8 rank layout using major-brand DRAM ICs. The part serves as a direct replacement for Hynix HMCG78AGBEA and HMCG78AGBEA081N server memory.
288-pin DDR5 form factor with no heat spreader
The 288-pin DDR5 DIMM fits standard unbuffered ECC slots in compatible servers and workstations. Without a heat spreader the module keeps a low profile for dense chassis or restricted airflow paths. Major-brand chipset components and factory testing target dependable operation under sustained workloads.
Upgrade from lower-capacity
Adding this 16GB stick increases total memory bandwidth at 5600MHz and extends ECC protection to larger datasets. The jump is worthwhile when current modules limit multitasking throughput or when a qualified Hynix replacement is required for validated platform support. Buyers needing registered RDIMM modules or higher-density ranks should verify platform requirements before purchase.
Öne çıkanlar
- ECC protection guards data integrity with built-in error correction
- DDR5 5600 MHz speed accelerates demanding server workloads
- 16 GB capacity expands memory headroom for virtualization
- 1 V standard voltage reduces power draw per module
- 288-pin UDIMM form factor fits compatible DDR5 server boards
Teknik özellikler
| Brand | A-Tech |
|---|---|
| Series | Compatible Replacement for Hynix HMCG78AGBEA HMCG78AGBEA081N |
| Model | A-Tech 16GB DDR5-5600 ECC UDIMM Server RAM Module |
| Capacity | 16GB |
| Type | 288-Pin DDR5 SDRAM |
| Speed | DDR5 5600 (PC5 44800) |
| CAS Latency | 40 |
| Voltage | 1.10V |
| ECC | Yes |
| Buffered/Registered | Unbuffered |
| Rank | 1Rx8 |
| Chipset | Major Brand Chipset |
| Heat Spreader | No |
| Features | Major Brand DRAM IC Chips |
Bu ürünle ilgili sorular
Does DDR5 5600 (PC5-44800) run at 5600 MT/s or drop to a lower speed?
The module is rated for DDR5 5600 MT/s (PC5-44800); actual speed depends on the platform's memory controller and BIOS configuration.
Will this 288-pin DDR5 UDIMM fit my server's DIMM slots?
It uses the standard 288-pin DDR5 UDIMM form factor; verify your system accepts unbuffered ECC DDR5 before installing.
How do I seat the module correctly and avoid the common mistake?
Align the off-centre notch with the slot key, press straight down until both retention clips click, and check your manual for the correct channel population order.
Bu reyondan diğerleri
Müşteriler bunları karşılaştırdı
Aynı raf, aynı sipariş tamamlama — sekiz koin ve 30 dakikalık kur kilidi.
