Neato Robotics
Neato Robotics 290-0056 Bumper Bump Switch Set Board for Botvac D3 D4 D5 D6
Replacement bumper switch board restores obstacle detection for Neato Botvac D3 through D6 models
- Compatible ManufacturerNeato
- Compatible ModelsBotvac D3, D4, D5, D6
- Dimensions3.1" (L) x 1.6" (W) x 0.4" (H)
- Weight0.05 lbs
- Genuine Neato part restores reliable obstacle detection for Botvac D3 D4 D5 D6
- Pre-installed connectors enable straightforward replacement without soldering or extra tools
- Compact board measuring 3.1" x 1.6" x .4" fits original mounting points exactly
- Lightweight at .05 lbs adds no noticeable mass to the bumper assembly
- OEM switch set (PN 290-0056) maintains factory sensing performance across compatible models
Neato Botvac D3-D6 Bumper Switch Board
This genuine Neato Robotics bumper bump switch set board (part 290-0056) restores obstacle detection for Botvac D3, D4, D5 and D6 robot vacuums. It arrives as a complete switch board with wiring and connectors already installed. The component fits directly into the bumper assembly without modification.
Mechanical Fit And Electrical Interface
The board measures 3.1" long, 1.6" wide and .4" high, weighing .05 lbs, so it sits inside the existing bumper cavity without altering clearances. Pre-installed connectors match the factory harness, limiting installation to a simple plug-in replacement. No soldering or firmware updates are required for the switch to communicate with the robot's main board.
Maintenance Scope And Limits
The switch set handles routine collision sensing for everyday cleaning cycles, registering impacts and signalling direction changes reliably. It does not address navigation mapping errors, battery degradation or motor wear elsewhere in the unit. Buyers needing a full bumper shell replacement or mainboard repair will require additional parts not included here.
Акценти
- Genuine Neato part restores reliable obstacle detection for Botvac D3 D4 D5 D6
- Pre-installed connectors enable straightforward replacement without soldering or extra tools
- Compact board measuring 3.1" x 1.6" x .4" fits original mounting points exactly
- Lightweight at .05 lbs adds no noticeable mass to the bumper assembly
- OEM switch set (PN 290-0056) maintains factory sensing performance across compatible models
Спецификации
| Brand | Neato Robotics |
|---|---|
| Model | 290-0056 |
| Part Number | 290-0056 |
| Compatible Manufacturer | Neato |
| Compatible Models | Botvac D3, D4, D5, D6 |
| Dimensions | 3.1" (L) x 1.6" (W) x 0.4" (H) |
| Weight | 0.05 lbs |
Въпроси за този артикул
How do I know this bumper switch board is the right part for my Botvac model?
The board carries part number 290-0056 and is listed for Botvac D3, D4, D5 and D6; match that number to the label on your existing board to confirm fit.
What change will I notice after installing this switch board?
The replacement restores the bumper's ability to register contact, so the robot resumes normal obstacle avoidance and turning behaviour.
How does the board connect to the robot's main electronics?
It ships with pre-installed wiring and connectors that plug directly into the existing harness, requiring no soldering or extra adapters.
Още от този рафт
Често сравнявани заедно
Същият рафт, същата каса — осем монети и заключване на курса за 30 минути.
No Sew
No Sew CQ42 5200 mAh 11.1 V laptop battery
- CQ42
- 5200 milliampere_ho…
23,99 щ.д.
0.00029677BTC
В наличност
CPY
CPY 3-Cell 11.4V 42Wh Battery for Dell Latitude 5280 5480 5580 Series
- Black
- Battery
21,99 щ.д.
0.00027203BTC
В наличност