Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Small green circuit board with black switch and white connectors 3.1 by 1.6 inches

Neato Robotics

Neato Robotics 290-0056 Bumper Bump Switch Set Board for Botvac D3 D4 D5 D6

SKU CH-3TJS-3S611

Replacement bumper switch board restores obstacle detection for Neato Botvac D3 through D6 models

  • Compatible ManufacturerNeato
  • Compatible ModelsBotvac D3, D4, D5, D6
  • Dimensions3.1" (L) x 1.6" (W) x 0.4" (H)
  • Weight0.05 lbs
  • Genuine Neato part restores reliable obstacle detection for Botvac D3 D4 D5 D6
  • Pre-installed connectors enable straightforward replacement without soldering or extra tools
  • Compact board measuring 3.1" x 1.6" x .4" fits original mounting points exactly
  • Lightweight at .05 lbs adds no noticeable mass to the bumper assembly
  • OEM switch set (PN 290-0056) maintains factory sensing performance across compatible models

Neato Botvac D3-D6 Bumper Switch Board

This genuine Neato Robotics bumper bump switch set board (part 290-0056) restores obstacle detection for Botvac D3, D4, D5 and D6 robot vacuums. It arrives as a complete switch board with wiring and connectors already installed. The component fits directly into the bumper assembly without modification.

Mechanical Fit And Electrical Interface

The board measures 3.1" long, 1.6" wide and .4" high, weighing .05 lbs, so it sits inside the existing bumper cavity without altering clearances. Pre-installed connectors match the factory harness, limiting installation to a simple plug-in replacement. No soldering or firmware updates are required for the switch to communicate with the robot's main board.

Maintenance Scope And Limits

The switch set handles routine collision sensing for everyday cleaning cycles, registering impacts and signalling direction changes reliably. It does not address navigation mapping errors, battery degradation or motor wear elsewhere in the unit. Buyers needing a full bumper shell replacement or mainboard repair will require additional parts not included here.

Høydepunkter

  • Genuine Neato part restores reliable obstacle detection for Botvac D3 D4 D5 D6
  • Pre-installed connectors enable straightforward replacement without soldering or extra tools
  • Compact board measuring 3.1" x 1.6" x .4" fits original mounting points exactly
  • Lightweight at .05 lbs adds no noticeable mass to the bumper assembly
  • OEM switch set (PN 290-0056) maintains factory sensing performance across compatible models

Spesifikasjoner

BrandNeato Robotics
Model290-0056
Part Number290-0056
Compatible ManufacturerNeato
Compatible ModelsBotvac D3, D4, D5, D6
Dimensions3.1" (L) x 1.6" (W) x 0.4" (H)
Weight0.05 lbs

Spørsmål om denne varen

How do I know this bumper switch board is the right part for my Botvac model?

The board carries part number 290-0056 and is listed for Botvac D3, D4, D5 and D6; match that number to the label on your existing board to confirm fit.

What change will I notice after installing this switch board?

The replacement restores the bumper's ability to register contact, so the robot resumes normal obstacle avoidance and turning behaviour.

How does the board connect to the robot's main electronics?

It ships with pre-installed wiring and connectors that plug directly into the existing harness, requiring no soldering or extra adapters.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.