Приемаме криптовалута — така монетите, които притежавате, могат да купят истински хардуер.Платете с крипто, похарчете го за истински хардуер. Безплатна застрахована доставка по целия свят над 399 $. Неутрални кашони без марка, изпратени от Германия.Безплатна застрахована доставка над 399 $. Курсът Ви е заключен за 30 минути веднага след отварянето на касата.Курс, заключен за 30 минути. Всеки артикул е запечатан, серийният му номер е проверен, и е покрит с 24-месечна гаранция.Запечатан, 24-месечна гаранция.

Проследени артикули Вход
Five small stainless steel MK8 nozzles with M6 threads and stamped size markings

Unique-Bargains

Unique-Bargains 0.3mm MK8 Stainless Steel Nozzle 1.75mm 5pcs

SKU CH-QFFR-7JE61

Pack of five stainless-steel MK8 nozzles with 0.3 mm bore for 1.75 mm filament

  • Precise 0.3 mm diameter enables fine-detail prints
  • Stainless steel construction resists wear from abrasive filaments
  • Five nozzles per pack provide ready replacements
  • M6 thread with 5 mm length fits MK8 hotends
  • Stamped size markings allow quick identification

Five-Pack 0.3 mm MK8 Nozzles

This set contains five stainless-steel nozzles stamped with their 0.3 mm bore size for quick identification. They are made for MK8 hot-ends that accept 1.75 mm filament and use an M6 thread with a 5 mm thread length. The pack suits owners of compatible printers who want spare or replacement tips on hand.

Consistent Machining and Clean Threads

Each nozzle has a smooth contact surface and a precisely machined orifice so filament flows evenly during printing. The M6 threads are clean and well formed, reducing the risk of cross-threading when you swap tips. Stainless steel resists wear better than brass, so the bore stays accurate through many hours of abrasive or standard filaments.

Direct Brass Replacement for Abrasive Filaments

These nozzles replace the standard brass tips that come on many MK8 extruders, letting you print carbon-fibre, glow-in-the-dark or other filled materials without rapid bore enlargement. The jump is worthwhile when you move beyond plain PLA, ABS or PCL and need a tip that holds its 0.3 mm diameter over long prints. After installation, recalibrate the nozzle-to-bed gap before starting a new job.

Акценти

  • Precise 0.3 mm diameter enables fine-detail prints
  • Stainless steel construction resists wear from abrasive filaments
  • Five nozzles per pack provide ready replacements
  • M6 thread with 5 mm length fits MK8 hotends
  • Stamped size markings allow quick identification

Спецификации

BrandUnique Bargains

Въпроси за този артикул

What thread standard does the MK8 nozzle use and what filament size does it limit?

The nozzle uses an M6 thread and is made for 1.75 mm filament only.

What are the physical dimensions and thread length needed to fit the hot-end?

Overall size is 13 mm long by 6 mm diameter with a 5 mm thread length.

How do I install the nozzle and which step is often missed?

Heat the block to the target temperature, hold the heat block with a spanner, unscrew the old nozzle, then tighten the new one; many forget to recalibrate the nozzle-to-bed gap afterwards.

Още от този рафт

Често сравнявани заедно

Същият рафт, същата каса — осем монети и заключване на курса за 30 минути.