Vi tar emot kryptovaluta — så att kryptot du äger kan köpa riktig hårdvara.Betala med krypto, använd det till riktig hårdvara. Fri, försäkrad frakt över hela världen vid köp över 399 $. Neutrala, omärkta ytterkartonger, skickade från Tyskland.Fri, försäkrad frakt över 399 $. Din kurs låses i 30 minuter så snart kassan öppnas.Kursen låst i 30 minuter. Varje artikel är förseglad, har kontrollerat serienummer och täcks av 24 månaders garanti.Förseglad, 24 månaders garanti.

Bevakade produkter Logga in
Five small stainless steel MK8 nozzles with M6 threads and stamped size markings

Unique-Bargains

Unique-Bargains 0.3mm MK8 Stainless Steel Nozzle 1.75mm 5pcs

SKU CH-QFFR-7JE61

Pack of five stainless-steel MK8 nozzles with 0.3 mm bore for 1.75 mm filament

  • Precise 0.3 mm diameter enables fine-detail prints
  • Stainless steel construction resists wear from abrasive filaments
  • Five nozzles per pack provide ready replacements
  • M6 thread with 5 mm length fits MK8 hotends
  • Stamped size markings allow quick identification

Five-Pack 0.3 mm MK8 Nozzles

This set contains five stainless-steel nozzles stamped with their 0.3 mm bore size for quick identification. They are made for MK8 hot-ends that accept 1.75 mm filament and use an M6 thread with a 5 mm thread length. The pack suits owners of compatible printers who want spare or replacement tips on hand.

Consistent Machining and Clean Threads

Each nozzle has a smooth contact surface and a precisely machined orifice so filament flows evenly during printing. The M6 threads are clean and well formed, reducing the risk of cross-threading when you swap tips. Stainless steel resists wear better than brass, so the bore stays accurate through many hours of abrasive or standard filaments.

Direct Brass Replacement for Abrasive Filaments

These nozzles replace the standard brass tips that come on many MK8 extruders, letting you print carbon-fibre, glow-in-the-dark or other filled materials without rapid bore enlargement. The jump is worthwhile when you move beyond plain PLA, ABS or PCL and need a tip that holds its 0.3 mm diameter over long prints. After installation, recalibrate the nozzle-to-bed gap before starting a new job.

I korthet

  • Precise 0.3 mm diameter enables fine-detail prints
  • Stainless steel construction resists wear from abrasive filaments
  • Five nozzles per pack provide ready replacements
  • M6 thread with 5 mm length fits MK8 hotends
  • Stamped size markings allow quick identification

Specifikationer

BrandUnique Bargains

Frågor om den här produkten

What thread standard does the MK8 nozzle use and what filament size does it limit?

The nozzle uses an M6 thread and is made for 1.75 mm filament only.

What are the physical dimensions and thread length needed to fit the hot-end?

Overall size is 13 mm long by 6 mm diameter with a 5 mm thread length.

How do I install the nozzle and which step is often missed?

Heat the block to the target temperature, hold the heat block with a spanner, unscrew the old nozzle, then tighten the new one; many forget to recalibrate the nozzle-to-bed gap afterwards.

Även i den här avdelningen

Andra har jämfört dessa

Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.