Vi tager imod kryptovaluta — så den krypto, du ejer, kan købe rigtig hardware.Betal med krypto, brug det på rigtig hardware. Gratis, forsikret levering til hele verden ved køb over 399 $. Neutrale, umærkede papkasser, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Din kurs låses i 30 minutter, så snart kassen åbner.Kurs låst i 30 minutter. Hver vare er forseglet, har kontrolleret serienummer og er dækket af 24 måneders garanti.Forseglet, 24 måneders garanti.

Prisvagt Log ind
Four green DDR5 UDIMM modules in a matched kit

NEMIX RAM

NEMIX RAM 128GB 4x32GB DDR5 5600MHz CL46 1.1V 2Rx8 UDIMM Supermicro X13SAW-F memory upgrade

SKU CH-XTY4-78KWK

128 GB kit of four 32 GB DDR5 modules running at 5600 MHz CL46 1.1 V, validated for Supermicro X13SAW-F motherboards

  • Capacity128GB (4 x 32GB)
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 128GB 4X32GB

  • 128GB total capacity from four 32GB modules for heavy multitasking
  • DDR5 5600MHz speed delivers high bandwidth for demanding workloads
  • CL46 latency at 1.1V balances responsiveness with efficient power use
  • 2Rx8 unbuffered UDIMM matches Supermicro X13SAW-F memory controller requirements
  • Built with major OEM chips from Samsung Micron or Hynix for tested stability

Exact-fit DDR5 5600 upgrade for Supermicro X13SAW-F

This 128 GB kit contains four 32 GB DDR5 5600 modules built to the precise 2Rx8, 1.1 V, CL46 specification the Supermicro X13SAW-F memory controller expects. Major OEM chips from Samsung, Micron or Hynix are tested at rated speed and voltage so the board recognises the full capacity immediately. The 288-pin unbuffered non-ECC UDIMM form factor matches the board's physical and electrical requirements without adapters.

Builders populating all four slots on this board

Suits anyone upgrading a Supermicro X13SAW-F desktop or workstation to the maximum 128 GB using the validated population order. Not for systems that require ECC registered DIMMs, SODIMM modules, a different DDR generation, or a voltage other than 1.1 V. Buyers needing lower capacities or higher speeds should verify their motherboard manual first.

2Rx8 rank and 1.1 V voltage decide compatibility

The board's memory controller is programmed for dual-rank 2Rx8 organisation at 1.1 V; modules with a different rank structure or voltage will not train at DDR5 5600 CL46. Confirm your manual lists this exact rank and voltage before ordering.

Fordele

  • 128GB total capacity from four 32GB modules for heavy multitasking
  • DDR5 5600MHz speed delivers high bandwidth for demanding workloads
  • CL46 latency at 1.1V balances responsiveness with efficient power use
  • 2Rx8 unbuffered UDIMM matches Supermicro X13SAW-F memory controller requirements
  • Built with major OEM chips from Samsung Micron or Hynix for tested stability

Specifikationer

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-328K4
Capacity128GB (4 x 32GB)
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content128GB 4X32GB DDR5 5600MHz PC5-44800 2Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

Andre versioner af denne model

5 flere i samme serie

Samme familie, men med anden hukommelse, køler eller clockfrekvens — sammenlign, før du bestemmer dig.

Spørgsmål om denne vare

Will these 288-pin DDR5 UDIMM modules fit the Supermicro X13SAW-F motherboard slots?

Yes, the kit is built to the exact 288-pin DDR5 UDIMM form factor required by the X13SAW-F, so each module seats directly in the board's DIMM sockets.

What is the correct installation order for the four 32 GB sticks on the X13SAW-F?

Populate the slots in the sequence shown in the motherboard manual — typically the two slots on one channel first, then the two on the second channel — to ensure the board recognises all 128 GB at DDR5-5600.

Do these non-ECC modules require any firmware updates or ongoing maintenance after install?

No firmware updates are needed; the modules run at 1.1 V with CL46 timings, and the only long-term care is keeping the system's interior free of dust so the chips stay cool.

Også på denne hylde

Kunderne har også sammenlignet disse

Samme hylde, samme kasse — otte mønter og 30 minutters kurslås.