Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Brass nozzle assembly with quick-release collar for Adventurer 5M series

Flashforge

Flashforge Nozzle Assembly Adventurer 5M Series 0.8mm 280C 3d printers accessory

SKU CH-S3K6-1TGGD

High-speed 0.8 mm nozzle delivers 32 mm³/s flow, heats to 280 °C in 35 seconds and swaps in three seconds for carbon-fibre and glass-fibre filaments

  • TypePrint Jet Head

Option 0.8mm

  • 0.6mm
  • 0.4mm
  • 0.25mm
  • 0.8mm

Läbikriipsutatud versioonid on olemas, kuid neid pole siin saadaval.

  • High-speed printing with 32 mm³/s flow rate
  • Reaches 200 °C in 35 seconds with 50 W heating
  • Prints advanced filaments up to 280 °C nozzle temperature
  • Quick-release design enables nozzle swap in 3 seconds
  • 8 mm diameter suits carbon fibre and glass fibre filaments

Nozzle for Adventurer 5M Series

This 0.8 mm nozzle assembly fits the Adventurer 5M and Adventurer 5M Pro printers. It supports filament types that require higher abrasion resistance such as carbon fibre, glass fibre, wood and speciality PLA blends. The quick-release mechanism lets you swap the nozzle in roughly three seconds without tools.

Sustained high-temperature printing

The nozzle reaches 200 °C in 35 seconds with a 50 W heater and maintains up to 280 °C for continuous extrusion. It delivers a volumetric flow of 32 mm³/s, so layer heights of 0.3 mm or 0.4 mm run steadily without the slowdowns seen in short-burst tests.

Upgrade from smaller diameters

Replacing a 0.25 mm or 0.4 mm nozzle with this 0.8 mm version cuts print time on large parts by using thicker layers. The jump is worth it when you print abrasive composites or need faster throughput and can accept the reduced detail of 0.3 mm to 0.4 mm layers.

Põhijooned

  • High-speed printing with 32 mm³/s flow rate
  • Reaches 200 °C in 35 seconds with 50 W heating
  • Prints advanced filaments up to 280 °C nozzle temperature
  • Quick-release design enables nozzle swap in 3 seconds
  • 8 mm diameter suits carbon fibre and glass fibre filaments

Tehnilised andmed

BrandFlashforge
TypePrint Jet Head

Küsimused selle toote kohta

How much heat and power does the 0.8 mm nozzle draw during a full-day print?

The nozzle runs on a 50 W heater that reaches 200 °C in 35 seconds and can sustain up to 280 °C for continuous printing.

Which printer must I already own for this nozzle to fit and work?

It is designed for the Flashforge Adventurer 5M series, matching the original print jet head on the AD5M and AD5M Pro.

Will the 0.8 mm nozzle work with the standard 0.4 mm hot-end parts I already have?

The 0.8 mm diameter is a separate quick-release nozzle; layer heights of 0.3 mm or 0.4 mm are recommended for efficient printing with abrasive filaments.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.