Acceptăm criptomonede — astfel, criptomonedele pe care le dețineți pot cumpăra echipamente reale.Plătiți în cripto, cheltuiți-o pe echipamente reale. Livrare asigurată gratuită oriunde în lume peste 399 $. Cartoane neutre, fără marcă, expediate din Germania.Livrare asigurată gratuită peste 399 $. Cursul dumneavoastră este blocat timp de 30 de minute de la deschiderea paginii de plată.Curs blocat 30 de minute. Fiecare articol este sigilat, numărul de serie este verificat, iar produsul este acoperit de o garanție de 24 de luni.Sigilat, garantat 24 de luni.

Produse urmărite Conectare
Brass nozzle assembly with quick-release collar for Adventurer 5M series

Flashforge

Flashforge Nozzle Assembly Adventurer 5M Series 0.8mm 280C 3d printers accessory

SKU CH-S3K6-1TGGD

High-speed 0.8 mm nozzle delivers 32 mm³/s flow, heats to 280 °C in 35 seconds and swaps in three seconds for carbon-fibre and glass-fibre filaments

  • TypePrint Jet Head

Option 0.8mm

  • 0.6mm
  • 0.4mm
  • 0.25mm
  • 0.8mm

Versiunile tăiate există, dar nu sunt disponibile aici.

  • High-speed printing with 32 mm³/s flow rate
  • Reaches 200 °C in 35 seconds with 50 W heating
  • Prints advanced filaments up to 280 °C nozzle temperature
  • Quick-release design enables nozzle swap in 3 seconds
  • 8 mm diameter suits carbon fibre and glass fibre filaments

Nozzle for Adventurer 5M Series

This 0.8 mm nozzle assembly fits the Adventurer 5M and Adventurer 5M Pro printers. It supports filament types that require higher abrasion resistance such as carbon fibre, glass fibre, wood and speciality PLA blends. The quick-release mechanism lets you swap the nozzle in roughly three seconds without tools.

Sustained high-temperature printing

The nozzle reaches 200 °C in 35 seconds with a 50 W heater and maintains up to 280 °C for continuous extrusion. It delivers a volumetric flow of 32 mm³/s, so layer heights of 0.3 mm or 0.4 mm run steadily without the slowdowns seen in short-burst tests.

Upgrade from smaller diameters

Replacing a 0.25 mm or 0.4 mm nozzle with this 0.8 mm version cuts print time on large parts by using thicker layers. The jump is worth it when you print abrasive composites or need faster throughput and can accept the reduced detail of 0.3 mm to 0.4 mm layers.

Puncte forte

  • High-speed printing with 32 mm³/s flow rate
  • Reaches 200 °C in 35 seconds with 50 W heating
  • Prints advanced filaments up to 280 °C nozzle temperature
  • Quick-release design enables nozzle swap in 3 seconds
  • 8 mm diameter suits carbon fibre and glass fibre filaments

Specificații

BrandFlashforge
TypePrint Jet Head

Întrebări despre acest articol

How much heat and power does the 0.8 mm nozzle draw during a full-day print?

The nozzle runs on a 50 W heater that reaches 200 °C in 35 seconds and can sustain up to 280 °C for continuous printing.

Which printer must I already own for this nozzle to fit and work?

It is designed for the Flashforge Adventurer 5M series, matching the original print jet head on the AD5M and AD5M Pro.

Will the 0.8 mm nozzle work with the standard 0.4 mm hot-end parts I already have?

The 0.8 mm diameter is a separate quick-release nozzle; layer heights of 0.3 mm or 0.4 mm are recommended for efficient printing with abrasive filaments.

Tot din acest raion

Clienții au comparat și acestea.

Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.