Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Green PoE HAT board with Ethernet port and 40-pin header inside black case

LORDWORLD

LORDWORLD PoE HAT (H) with Case for Raspberry Pi 5 / CM 5 development board

SKU CH-S9G2-JTG7A

A Power-over-Ethernet HAT delivering 5 V 5 A to a Raspberry Pi 5 or CM 5 through the standard 40-pin header while supporting IEEE 802.3 af/at and fitting the official case and active cooler

  • Powers Raspberry Pi 5 via single Ethernet cable using IEEE 802.3 af/at standard
  • Delivers 5 V 5 A output through isolated switched-mode supply for stable operation
  • Fits standard 40-pin GPIO header and assembles inside official Raspberry Pi 5 case
  • Works with Raspberry Pi 5 and Compute Module 5 development boards
  • Compatible with official Raspberry Pi 5 active cooler for thermal management

PoE HAT (H) for Raspberry Pi 5 and CM 5

This expansion board delivers both network connectivity and 5 V 5 A power to a Raspberry Pi 5 or CM 5 through a single Ethernet cable. It is built for makers and developers who need a compact, cable-reduced setup for edge or IoT projects.

Check your PoE infrastructure and case plans

The board follows the IEEE 802.3 af/at standard, so your switch or injector must support that specification. It uses the standard 40-pin GPIO header and fits inside the official Raspberry Pi 5 case, but it will not work with boards that lack the 40-pin connector or with cases that do not accommodate the HAT footprint.

Thermals, noise and power draw in normal use

The isolated switched-mode supply runs silently because it has no moving parts. Heat output is low at the rated 5 V 5 A load, and the design leaves the Pi 5's official active cooler fully accessible for CPU thermal management.

Põhijooned

  • Powers Raspberry Pi 5 via single Ethernet cable using IEEE 802.3 af/at standard
  • Delivers 5 V 5 A output through isolated switched-mode supply for stable operation
  • Fits standard 40-pin GPIO header and assembles inside official Raspberry Pi 5 case
  • Works with Raspberry Pi 5 and Compute Module 5 development boards
  • Compatible with official Raspberry Pi 5 active cooler for thermal management

Tehnilised andmed

BrandLORDWORLD

Küsimused selle toote kohta

What comes in the box and does it include the Raspberry Pi 5 or CM 5 board?

The package contains the PoE HAT (H) expansion board and a case. The Raspberry Pi 5 or Compute Module 5 development board must be purchased separately.

Which PoE standard does this HAT support for the Raspberry Pi 5 or CM 5?

It supports the IEEE 802.3 af/at network standard, delivering up to 5V 5A output through a single Ethernet cable.

How does the 40-pin GPIO header affect fitting the board inside the official Raspberry Pi 5 case?

The standard 40-pin GPIO header allows the HAT to assemble directly into the official Raspberry Pi 5 case and remains compatible with the official active cooler.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.