Vi tar emot kryptovaluta — så att kryptot du äger kan köpa riktig hårdvara.Betala med krypto, använd det till riktig hårdvara. Fri, försäkrad frakt över hela världen vid köp över 399 $. Neutrala, omärkta ytterkartonger, skickade från Tyskland.Fri, försäkrad frakt över 399 $. Din kurs låses i 30 minuter så snart kassan öppnas.Kursen låst i 30 minuter. Varje artikel är förseglad, har kontrollerat serienummer och täcks av 24 månaders garanti.Förseglad, 24 månaders garanti.

Bevakade produkter Logga in
Green PoE HAT board with Ethernet port and 40-pin header inside black case

LORDWORLD

LORDWORLD PoE HAT (H) with Case for Raspberry Pi 5 / CM 5 development board

SKU CH-S9G2-JTG7A

A Power-over-Ethernet HAT delivering 5 V 5 A to a Raspberry Pi 5 or CM 5 through the standard 40-pin header while supporting IEEE 802.3 af/at and fitting the official case and active cooler

  • Powers Raspberry Pi 5 via single Ethernet cable using IEEE 802.3 af/at standard
  • Delivers 5 V 5 A output through isolated switched-mode supply for stable operation
  • Fits standard 40-pin GPIO header and assembles inside official Raspberry Pi 5 case
  • Works with Raspberry Pi 5 and Compute Module 5 development boards
  • Compatible with official Raspberry Pi 5 active cooler for thermal management

PoE HAT (H) for Raspberry Pi 5 and CM 5

This expansion board delivers both network connectivity and 5 V 5 A power to a Raspberry Pi 5 or CM 5 through a single Ethernet cable. It is built for makers and developers who need a compact, cable-reduced setup for edge or IoT projects.

Check your PoE infrastructure and case plans

The board follows the IEEE 802.3 af/at standard, so your switch or injector must support that specification. It uses the standard 40-pin GPIO header and fits inside the official Raspberry Pi 5 case, but it will not work with boards that lack the 40-pin connector or with cases that do not accommodate the HAT footprint.

Thermals, noise and power draw in normal use

The isolated switched-mode supply runs silently because it has no moving parts. Heat output is low at the rated 5 V 5 A load, and the design leaves the Pi 5's official active cooler fully accessible for CPU thermal management.

I korthet

  • Powers Raspberry Pi 5 via single Ethernet cable using IEEE 802.3 af/at standard
  • Delivers 5 V 5 A output through isolated switched-mode supply for stable operation
  • Fits standard 40-pin GPIO header and assembles inside official Raspberry Pi 5 case
  • Works with Raspberry Pi 5 and Compute Module 5 development boards
  • Compatible with official Raspberry Pi 5 active cooler for thermal management

Specifikationer

BrandLORDWORLD

Frågor om den här produkten

What comes in the box and does it include the Raspberry Pi 5 or CM 5 board?

The package contains the PoE HAT (H) expansion board and a case. The Raspberry Pi 5 or Compute Module 5 development board must be purchased separately.

Which PoE standard does this HAT support for the Raspberry Pi 5 or CM 5?

It supports the IEEE 802.3 af/at network standard, delivering up to 5V 5A output through a single Ethernet cable.

How does the 40-pin GPIO header affect fitting the board inside the official Raspberry Pi 5 case?

The standard 40-pin GPIO header allows the HAT to assemble directly into the official Raspberry Pi 5 case and remains compatible with the official active cooler.

Även i den här avdelningen

Andra har jämfört dessa

Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.