نقبل الدفع بالعملة المشفرة — لذلك يمكن للعملات الرقمية التي تملكها أن تشتري أجهزة حقيقية.ادفع بالعملة المشفرة، وأنفقها على أجهزة حقيقية. شحن مؤمن مجانا إلى كل أنحاء العالم لما يتجاوز 399 US$. صناديق شحن بسيطة بلا علامة تجارية، ترسل من ألمانيا.شحن مؤمن مجانا لما يتجاوز 399 US$. يُقفل سعرك لمدة 30 دقيقة بمجرد فتح صفحة الدفع.السعر مقفل لمدة 30 دقيقة. كل قطعة مختومة، ورقمها التسلسلي متحقق منه، ومشمولة بضمان 24 شهرا.مختوم، وبضمان 24 شهرا.

قائمة الرصد تسجيل الدخول
Green PoE HAT board with Ethernet port and 40-pin header inside black case

LORDWORLD

LORDWORLD PoE HAT (H) with Case for Raspberry Pi 5 / CM 5 development board

SKU CH-S9G2-JTG7A

A Power-over-Ethernet HAT delivering 5 V 5 A to a Raspberry Pi 5 or CM 5 through the standard 40-pin header while supporting IEEE 802.3 af/at and fitting the official case and active cooler

  • Powers Raspberry Pi 5 via single Ethernet cable using IEEE 802.3 af/at standard
  • Delivers 5 V 5 A output through isolated switched-mode supply for stable operation
  • Fits standard 40-pin GPIO header and assembles inside official Raspberry Pi 5 case
  • Works with Raspberry Pi 5 and Compute Module 5 development boards
  • Compatible with official Raspberry Pi 5 active cooler for thermal management

PoE HAT (H) for Raspberry Pi 5 and CM 5

This expansion board delivers both network connectivity and 5 V 5 A power to a Raspberry Pi 5 or CM 5 through a single Ethernet cable. It is built for makers and developers who need a compact, cable-reduced setup for edge or IoT projects.

Check your PoE infrastructure and case plans

The board follows the IEEE 802.3 af/at standard, so your switch or injector must support that specification. It uses the standard 40-pin GPIO header and fits inside the official Raspberry Pi 5 case, but it will not work with boards that lack the 40-pin connector or with cases that do not accommodate the HAT footprint.

Thermals, noise and power draw in normal use

The isolated switched-mode supply runs silently because it has no moving parts. Heat output is low at the rated 5 V 5 A load, and the design leaves the Pi 5's official active cooler fully accessible for CPU thermal management.

أبرز المميزات

  • Powers Raspberry Pi 5 via single Ethernet cable using IEEE 802.3 af/at standard
  • Delivers 5 V 5 A output through isolated switched-mode supply for stable operation
  • Fits standard 40-pin GPIO header and assembles inside official Raspberry Pi 5 case
  • Works with Raspberry Pi 5 and Compute Module 5 development boards
  • Compatible with official Raspberry Pi 5 active cooler for thermal management

المواصفات

BrandLORDWORLD

أسئلة حول هذا المنتج

What comes in the box and does it include the Raspberry Pi 5 or CM 5 board?

The package contains the PoE HAT (H) expansion board and a case. The Raspberry Pi 5 or Compute Module 5 development board must be purchased separately.

Which PoE standard does this HAT support for the Raspberry Pi 5 or CM 5?

It supports the IEEE 802.3 af/at network standard, delivering up to 5V 5A output through a single Ethernet cable.

How does the 40-pin GPIO header affect fitting the board inside the official Raspberry Pi 5 case?

The standard 40-pin GPIO header allows the HAT to assemble directly into the official Raspberry Pi 5 case and remains compatible with the official active cooler.

أيضًا في هذا القسم

عملاء قارنوا هذه المنتجات

نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.