Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Green PoE HAT board with Ethernet port and 40-pin header inside black case

LORDWORLD

LORDWORLD PoE HAT (H) with Case for Raspberry Pi 5 / CM 5 development board

SKU CH-S9G2-JTG7A

A Power-over-Ethernet HAT delivering 5 V 5 A to a Raspberry Pi 5 or CM 5 through the standard 40-pin header while supporting IEEE 802.3 af/at and fitting the official case and active cooler

  • Powers Raspberry Pi 5 via single Ethernet cable using IEEE 802.3 af/at standard
  • Delivers 5 V 5 A output through isolated switched-mode supply for stable operation
  • Fits standard 40-pin GPIO header and assembles inside official Raspberry Pi 5 case
  • Works with Raspberry Pi 5 and Compute Module 5 development boards
  • Compatible with official Raspberry Pi 5 active cooler for thermal management

PoE HAT (H) for Raspberry Pi 5 and CM 5

This expansion board delivers both network connectivity and 5 V 5 A power to a Raspberry Pi 5 or CM 5 through a single Ethernet cable. It is built for makers and developers who need a compact, cable-reduced setup for edge or IoT projects.

Check your PoE infrastructure and case plans

The board follows the IEEE 802.3 af/at standard, so your switch or injector must support that specification. It uses the standard 40-pin GPIO header and fits inside the official Raspberry Pi 5 case, but it will not work with boards that lack the 40-pin connector or with cases that do not accommodate the HAT footprint.

Thermals, noise and power draw in normal use

The isolated switched-mode supply runs silently because it has no moving parts. Heat output is low at the rated 5 V 5 A load, and the design leaves the Pi 5's official active cooler fully accessible for CPU thermal management.

Helstu kostir

  • Powers Raspberry Pi 5 via single Ethernet cable using IEEE 802.3 af/at standard
  • Delivers 5 V 5 A output through isolated switched-mode supply for stable operation
  • Fits standard 40-pin GPIO header and assembles inside official Raspberry Pi 5 case
  • Works with Raspberry Pi 5 and Compute Module 5 development boards
  • Compatible with official Raspberry Pi 5 active cooler for thermal management

Tæknilýsing

BrandLORDWORLD

Spurningar um þessa vöru

What comes in the box and does it include the Raspberry Pi 5 or CM 5 board?

The package contains the PoE HAT (H) expansion board and a case. The Raspberry Pi 5 or Compute Module 5 development board must be purchased separately.

Which PoE standard does this HAT support for the Raspberry Pi 5 or CM 5?

It supports the IEEE 802.3 af/at network standard, delivering up to 5V 5A output through a single Ethernet cable.

How does the 40-pin GPIO header affect fitting the board inside the official Raspberry Pi 5 case?

The standard 40-pin GPIO header allows the HAT to assemble directly into the official Raspberry Pi 5 case and remains compatible with the official active cooler.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.