SanDisk
SanDisk Cruzer Blade 8 GB USB 2.0 USB flash drive Black SDCZ50-008G-B35
391,99 $
0.00499071BTC
Laos
NEMIX RAM
NEMIX RAM 8GB DDR4 2133 PC4-17000 CL15 260-pin SODIMM memory upgrade
DDR4 2133 SODIMM adds 8 GB of non-ECC memory to the POSIFLEX XT-6315E terminal at 1.2 V and CL15 latency
- Capacity8GB
- SpeedDDR4 2133 (PC4 17000)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.20V
- 8GB DDR4 capacity boosts POS terminal responsiveness
- 2133MHz speed with CL15 latency handles transaction workloads
- 2V low-voltage operation reduces heat in fanless systems
- 260-pin SODIMM form factor fits POSIFLEX XT-6315E exactly
- Major OEM chips from Samsung, Micron or Hynix ensure reliability
Targeted POS memory upgrade
This 8GB SODIMM module is built for the POSIFLEX XT-6315E JIVA High-End Fanless POS Terminal with Celeron Chipset. It delivers a direct DDR4 2133 upgrade for point-of-sale systems requiring reliable, low-voltage memory. The unbuffered, non-ECC design matches the platform's native requirements. Installers can add capacity without configuration changes.
Single-rank capacity for transaction workloads
The 8GB density handles typical POS software, local databases and peripheral drivers with comfortable headroom. Dual-rank 2Rx8 organisation supports the memory controller's interleaving for steady throughput at 2133 MT/s. Workloads that exceed 8GB will page to storage, increasing latency during peak checkout periods. The module fills one 260-pin slot and leaves no room for a second stick in single-slot terminals.
Low-voltage operation in fanless chassis
Rated at 1.20V, the module draws minimal power and generates little heat inside the sealed POS enclosure. Samsung, Micron or Hynix DRAM chips are stress-tested under load before shipping. No heat spreader is fitted, relying on the terminal's passive thermal design. Silent operation is maintained because the memory adds no active cooling requirement.
Põhijooned
- 8GB DDR4 capacity boosts POS terminal responsiveness
- 2133MHz speed with CL15 latency handles transaction workloads
- 2V low-voltage operation reduces heat in fanless systems
- 260-pin SODIMM form factor fits POSIFLEX XT-6315E exactly
- Major OEM chips from Samsung, Micron or Hynix ensure reliability
Tehnilised andmed
| Brand | NEMIX RAM |
|---|---|
| Series | POSIFLEX POS Series Point of Sale Kiosk Memory |
| Model | POSIFLEX POS DDR4 2133MHZ Non-ECC Unbuffered SODIMM |
| Part Number | MS17000-828K1 |
| Capacity | 8GB |
| Speed | DDR4 2133 (PC4 17000) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.20V |
| Compatible System | POSIFLEX POS |
| CAS Latency | CL15 |
| Heat Spreader | No |
| Type | 260-Pin DDR4 SODIMM |
| Rank | 2Rx8 |
| Features | DDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible |
| Package Content | 8GB (1X8GB) DDR4 2133MHZ PC4-17000 2Rx8 1.2V CL15 260-PIN Non-ECC Unbuffered SODIMM |
Küsimused selle toote kohta
Will this DDR4 2133 CL15 SODIMM run alongside the original memory in my POSIFLEX XT-6315E terminal?
Yes, the module matches the terminal's DDR4 2133 specification, 1.2 V voltage and CL15 timing, so it will operate at the same speed and latency as the factory-installed memory.
How can I verify the 8 GB module is recognised and running at PC4-17000 after installation?
Enter the system BIOS or UEFI and confirm the memory size shows 8 GB, speed reads 2133 MT/s and CAS latency reads 15.
Does the MS17000-828K1 package include any tools, brackets or thermal pads, or must I buy them separately?
The package contains only the 8 GB 260-pin SODIMM; no tools, brackets or thermal pads are included.
Veel samast osakonnast
Kliendid võrdlesid neid ka
Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.
