We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in

NEMIX RAM

NEMIX RAM 8GB DDR4 2133 PC4-17000 CL15 260-pin SODIMM memory upgrade

SKU CH-WCC1-H2A5E

DDR4 2133 SODIMM adds 8 GB of non-ECC memory to the POSIFLEX XT-6315E terminal at 1.2 V and CL15 latency

  • Capacity8GB
  • SpeedDDR4 2133 (PC4 17000)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.20V
  • 8GB DDR4 capacity boosts POS terminal responsiveness
  • 2133MHz speed with CL15 latency handles transaction workloads
  • 2V low-voltage operation reduces heat in fanless systems
  • 260-pin SODIMM form factor fits POSIFLEX XT-6315E exactly
  • Major OEM chips from Samsung, Micron or Hynix ensure reliability

Targeted POS memory upgrade

This 8GB SODIMM module is built for the POSIFLEX XT-6315E JIVA High-End Fanless POS Terminal with Celeron Chipset. It delivers a direct DDR4 2133 upgrade for point-of-sale systems requiring reliable, low-voltage memory. The unbuffered, non-ECC design matches the platform's native requirements. Installers can add capacity without configuration changes.

Single-rank capacity for transaction workloads

The 8GB density handles typical POS software, local databases and peripheral drivers with comfortable headroom. Dual-rank 2Rx8 organisation supports the memory controller's interleaving for steady throughput at 2133 MT/s. Workloads that exceed 8GB will page to storage, increasing latency during peak checkout periods. The module fills one 260-pin slot and leaves no room for a second stick in single-slot terminals.

Low-voltage operation in fanless chassis

Rated at 1.20V, the module draws minimal power and generates little heat inside the sealed POS enclosure. Samsung, Micron or Hynix DRAM chips are stress-tested under load before shipping. No heat spreader is fitted, relying on the terminal's passive thermal design. Silent operation is maintained because the memory adds no active cooling requirement.

Highlights

  • 8GB DDR4 capacity boosts POS terminal responsiveness
  • 2133MHz speed with CL15 latency handles transaction workloads
  • 2V low-voltage operation reduces heat in fanless systems
  • 260-pin SODIMM form factor fits POSIFLEX XT-6315E exactly
  • Major OEM chips from Samsung, Micron or Hynix ensure reliability

Specifications

BrandNEMIX RAM
SeriesPOSIFLEX POS Series Point of Sale Kiosk Memory
ModelPOSIFLEX POS DDR4 2133MHZ Non-ECC Unbuffered SODIMM
Part NumberMS17000-828K1
Capacity8GB
SpeedDDR4 2133 (PC4 17000)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.20V
Compatible SystemPOSIFLEX POS
CAS LatencyCL15
Heat SpreaderNo
Type260-Pin DDR4 SODIMM
Rank2Rx8
FeaturesDDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content8GB (1X8GB) DDR4 2133MHZ PC4-17000 2Rx8 1.2V CL15 260-PIN Non-ECC Unbuffered SODIMM

Questions about this item

Will this DDR4 2133 CL15 SODIMM run alongside the original memory in my POSIFLEX XT-6315E terminal?

Yes, the module matches the terminal's DDR4 2133 specification, 1.2 V voltage and CL15 timing, so it will operate at the same speed and latency as the factory-installed memory.

How can I verify the 8 GB module is recognised and running at PC4-17000 after installation?

Enter the system BIOS or UEFI and confirm the memory size shows 8 GB, speed reads 2133 MT/s and CAS latency reads 15.

Does the MS17000-828K1 package include any tools, brackets or thermal pads, or must I buy them separately?

The package contains only the 8 GB 260-pin SODIMM; no tools, brackets or thermal pads are included.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.