SanDisk
SanDisk Cruzer Blade 8 GB USB 2.0 USB flash drive Black SDCZ50-008G-B35
391.99 US$
0.00503973BTC
متوفر
NEMIX RAM
NEMIX RAM 8GB DDR4 2133 PC4-17000 CL15 260-pin SODIMM memory upgrade
DDR4 2133 SODIMM adds 8 GB of non-ECC memory to the POSIFLEX XT-6315E terminal at 1.2 V and CL15 latency
- Capacity8GB
- SpeedDDR4 2133 (PC4 17000)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.20V
- 8GB DDR4 capacity boosts POS terminal responsiveness
- 2133MHz speed with CL15 latency handles transaction workloads
- 2V low-voltage operation reduces heat in fanless systems
- 260-pin SODIMM form factor fits POSIFLEX XT-6315E exactly
- Major OEM chips from Samsung, Micron or Hynix ensure reliability
Targeted POS memory upgrade
This 8GB SODIMM module is built for the POSIFLEX XT-6315E JIVA High-End Fanless POS Terminal with Celeron Chipset. It delivers a direct DDR4 2133 upgrade for point-of-sale systems requiring reliable, low-voltage memory. The unbuffered, non-ECC design matches the platform's native requirements. Installers can add capacity without configuration changes.
Single-rank capacity for transaction workloads
The 8GB density handles typical POS software, local databases and peripheral drivers with comfortable headroom. Dual-rank 2Rx8 organisation supports the memory controller's interleaving for steady throughput at 2133 MT/s. Workloads that exceed 8GB will page to storage, increasing latency during peak checkout periods. The module fills one 260-pin slot and leaves no room for a second stick in single-slot terminals.
Low-voltage operation in fanless chassis
Rated at 1.20V, the module draws minimal power and generates little heat inside the sealed POS enclosure. Samsung, Micron or Hynix DRAM chips are stress-tested under load before shipping. No heat spreader is fitted, relying on the terminal's passive thermal design. Silent operation is maintained because the memory adds no active cooling requirement.
أبرز المميزات
- 8GB DDR4 capacity boosts POS terminal responsiveness
- 2133MHz speed with CL15 latency handles transaction workloads
- 2V low-voltage operation reduces heat in fanless systems
- 260-pin SODIMM form factor fits POSIFLEX XT-6315E exactly
- Major OEM chips from Samsung, Micron or Hynix ensure reliability
المواصفات
| Brand | NEMIX RAM |
|---|---|
| Series | POSIFLEX POS Series Point of Sale Kiosk Memory |
| Model | POSIFLEX POS DDR4 2133MHZ Non-ECC Unbuffered SODIMM |
| Part Number | MS17000-828K1 |
| Capacity | 8GB |
| Speed | DDR4 2133 (PC4 17000) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.20V |
| Compatible System | POSIFLEX POS |
| CAS Latency | CL15 |
| Heat Spreader | No |
| Type | 260-Pin DDR4 SODIMM |
| Rank | 2Rx8 |
| Features | DDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible |
| Package Content | 8GB (1X8GB) DDR4 2133MHZ PC4-17000 2Rx8 1.2V CL15 260-PIN Non-ECC Unbuffered SODIMM |
أسئلة حول هذا المنتج
Will this DDR4 2133 CL15 SODIMM run alongside the original memory in my POSIFLEX XT-6315E terminal?
Yes, the module matches the terminal's DDR4 2133 specification, 1.2 V voltage and CL15 timing, so it will operate at the same speed and latency as the factory-installed memory.
How can I verify the 8 GB module is recognised and running at PC4-17000 after installation?
Enter the system BIOS or UEFI and confirm the memory size shows 8 GB, speed reads 2133 MT/s and CAS latency reads 15.
Does the MS17000-828K1 package include any tools, brackets or thermal pads, or must I buy them separately?
The package contains only the 8 GB 260-pin SODIMM; no tools, brackets or thermal pads are included.
أيضًا في هذا القسم
عملاء قارنوا هذه المنتجات
نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.
