Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Eight spools of silk PLA filament in white orange yellow and green

PrintOxe

PrintOxe PLA Silk Filament 8 Pack 1.75mm 8kg 2W 2O 2Y 2G

SKU CH-P3ZR-T7DGM

Eight spools of 1.75 mm PLA silk filament in white, orange, yellow and green totalling 8 kg net weight

  • Color2White+2Orange+2Yellow+2Green
  • TypePLA Filament like SILK
  • 8 kg total filament gives plenty of material for large projects
  • Silk-like finish creates a glossy, smooth surface on every print
  • Vacuum-sealed spools with desiccant protect filament from moisture
  • 75 mm diameter works with most popular 3D printers
  • Print at 200 °C – 220 °C for reliable extrusion

Eight-colour silk PLA bundle

This eight-spool pack delivers 1.75 mm silk-effect PLA in white, orange, yellow and green, two spools of each colour. Each spool holds 1 kg net filament for a total of 8 kg, aimed at makers who want a ready palette for decorative prints without ordering separate reels.

Consistent extrusion on long prints

The material is formulated from 100 % high-purity corn-starch PLA to minimise shrinkage and warping during extended sessions. Recommended nozzle temperature sits between 200 °C and 220 °C, and the vacuum-sealed spools with desiccant keep moisture absorption low so flow stays steady over many hours.

Standard spool fits common printers

Spools measure 7.88 in diameter, 2.69 in width with a 2.20 in hub hole, matching the dimensions used by most desktop machines. Filament loads straight onto typical holders, though printers with very small enclosed spool bays or non-standard hub sizes may need an adapter or external feed.

Põhijooned

  • 8 kg total filament gives plenty of material for large projects
  • Silk-like finish creates a glossy, smooth surface on every print
  • Vacuum-sealed spools with desiccant protect filament from moisture
  • 75 mm diameter works with most popular 3D printers
  • Print at 200 °C – 220 °C for reliable extrusion

Tehnilised andmed

BrandPRINTOXE
Color2White+2Orange+2Yellow+2Green
TypePLA Filament like SILK

Küsimused selle toote kohta

Does the silk PLA filament produce more heat or need higher nozzle power during long prints?

The recommended nozzle temperature is 200°C to 220°C (392°F to 428°F), the same range as standard PLA, so it does not demand extra heat or power for extended printing.

What printer hardware must I already have to use these 1.75 mm spools?

A 3D printer that accepts 1.75 mm filament and spools with a 5.59 cm hub hole, 20.015 cm outer diameter and 6.83 cm width — dimensions that fit most common desktop machines.

Will the filament work on an older printer that only has a basic heated bed and no enclosure?

Yes, the material is designed for standard PLA temperatures and minimal warping, so it prints reliably on older open-frame printers with a heated bed.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.