Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Eight spools of silk PLA filament in white orange yellow and green

PrintOxe

PrintOxe PLA Silk Filament 8 Pack 1.75mm 8kg 2W 2O 2Y 2G

SKU CH-P3ZR-T7DGM

Eight spools of 1.75 mm PLA silk filament in white, orange, yellow and green totalling 8 kg net weight

  • Color2White+2Orange+2Yellow+2Green
  • TypePLA Filament like SILK
  • 8 kg total filament gives plenty of material for large projects
  • Silk-like finish creates a glossy, smooth surface on every print
  • Vacuum-sealed spools with desiccant protect filament from moisture
  • 75 mm diameter works with most popular 3D printers
  • Print at 200 °C – 220 °C for reliable extrusion

Eight-colour silk PLA bundle

This eight-spool pack delivers 1.75 mm silk-effect PLA in white, orange, yellow and green, two spools of each colour. Each spool holds 1 kg net filament for a total of 8 kg, aimed at makers who want a ready palette for decorative prints without ordering separate reels.

Consistent extrusion on long prints

The material is formulated from 100 % high-purity corn-starch PLA to minimise shrinkage and warping during extended sessions. Recommended nozzle temperature sits between 200 °C and 220 °C, and the vacuum-sealed spools with desiccant keep moisture absorption low so flow stays steady over many hours.

Standard spool fits common printers

Spools measure 7.88 in diameter, 2.69 in width with a 2.20 in hub hole, matching the dimensions used by most desktop machines. Filament loads straight onto typical holders, though printers with very small enclosed spool bays or non-standard hub sizes may need an adapter or external feed.

Høydepunkter

  • 8 kg total filament gives plenty of material for large projects
  • Silk-like finish creates a glossy, smooth surface on every print
  • Vacuum-sealed spools with desiccant protect filament from moisture
  • 75 mm diameter works with most popular 3D printers
  • Print at 200 °C – 220 °C for reliable extrusion

Spesifikasjoner

BrandPRINTOXE
Color2White+2Orange+2Yellow+2Green
TypePLA Filament like SILK

Spørsmål om denne varen

Does the silk PLA filament produce more heat or need higher nozzle power during long prints?

The recommended nozzle temperature is 200°C to 220°C (392°F to 428°F), the same range as standard PLA, so it does not demand extra heat or power for extended printing.

What printer hardware must I already have to use these 1.75 mm spools?

A 3D printer that accepts 1.75 mm filament and spools with a 5.59 cm hub hole, 20.015 cm outer diameter and 6.83 cm width — dimensions that fit most common desktop machines.

Will the filament work on an older printer that only has a basic heated bed and no enclosure?

Yes, the material is designed for standard PLA temperatures and minimal warping, so it prints reliably on older open-frame printers with a heated bed.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.