Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Eight spools of silk PLA filament in white orange yellow and green

PrintOxe

PrintOxe PLA Silk Filament 8 Pack 1.75mm 8kg 2W 2O 2Y 2G

SKU CH-P3ZR-T7DGM

Eight spools of 1.75 mm PLA silk filament in white, orange, yellow and green totalling 8 kg net weight

  • Color2White+2Orange+2Yellow+2Green
  • TypePLA Filament like SILK
  • 8 kg total filament gives plenty of material for large projects
  • Silk-like finish creates a glossy, smooth surface on every print
  • Vacuum-sealed spools with desiccant protect filament from moisture
  • 75 mm diameter works with most popular 3D printers
  • Print at 200 °C – 220 °C for reliable extrusion

Eight-colour silk PLA bundle

This eight-spool pack delivers 1.75 mm silk-effect PLA in white, orange, yellow and green, two spools of each colour. Each spool holds 1 kg net filament for a total of 8 kg, aimed at makers who want a ready palette for decorative prints without ordering separate reels.

Consistent extrusion on long prints

The material is formulated from 100 % high-purity corn-starch PLA to minimise shrinkage and warping during extended sessions. Recommended nozzle temperature sits between 200 °C and 220 °C, and the vacuum-sealed spools with desiccant keep moisture absorption low so flow stays steady over many hours.

Standard spool fits common printers

Spools measure 7.88 in diameter, 2.69 in width with a 2.20 in hub hole, matching the dimensions used by most desktop machines. Filament loads straight onto typical holders, though printers with very small enclosed spool bays or non-standard hub sizes may need an adapter or external feed.

Helstu kostir

  • 8 kg total filament gives plenty of material for large projects
  • Silk-like finish creates a glossy, smooth surface on every print
  • Vacuum-sealed spools with desiccant protect filament from moisture
  • 75 mm diameter works with most popular 3D printers
  • Print at 200 °C – 220 °C for reliable extrusion

Tæknilýsing

BrandPRINTOXE
Color2White+2Orange+2Yellow+2Green
TypePLA Filament like SILK

Spurningar um þessa vöru

Does the silk PLA filament produce more heat or need higher nozzle power during long prints?

The recommended nozzle temperature is 200°C to 220°C (392°F to 428°F), the same range as standard PLA, so it does not demand extra heat or power for extended printing.

What printer hardware must I already have to use these 1.75 mm spools?

A 3D printer that accepts 1.75 mm filament and spools with a 5.59 cm hub hole, 20.015 cm outer diameter and 6.83 cm width — dimensions that fit most common desktop machines.

Will the filament work on an older printer that only has a basic heated bed and no enclosure?

Yes, the material is designed for standard PLA temperatures and minimal warping, so it prints reliably on older open-frame printers with a heated bed.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.