Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Eight spools of silk PLA filament in white orange yellow and green

PrintOxe

PrintOxe PLA Silk Filament 8 Pack 1.75mm 8kg 2W 2O 2Y 2G

SKU CH-P3ZR-T7DGM

Eight spools of 1.75 mm PLA silk filament in white, orange, yellow and green totalling 8 kg net weight

  • Color2White+2Orange+2Yellow+2Green
  • TypePLA Filament like SILK
  • 8 kg total filament gives plenty of material for large projects
  • Silk-like finish creates a glossy, smooth surface on every print
  • Vacuum-sealed spools with desiccant protect filament from moisture
  • 75 mm diameter works with most popular 3D printers
  • Print at 200 °C – 220 °C for reliable extrusion

Eight-colour silk PLA bundle

This eight-spool pack delivers 1.75 mm silk-effect PLA in white, orange, yellow and green, two spools of each colour. Each spool holds 1 kg net filament for a total of 8 kg, aimed at makers who want a ready palette for decorative prints without ordering separate reels.

Consistent extrusion on long prints

The material is formulated from 100 % high-purity corn-starch PLA to minimise shrinkage and warping during extended sessions. Recommended nozzle temperature sits between 200 °C and 220 °C, and the vacuum-sealed spools with desiccant keep moisture absorption low so flow stays steady over many hours.

Standard spool fits common printers

Spools measure 7.88 in diameter, 2.69 in width with a 2.20 in hub hole, matching the dimensions used by most desktop machines. Filament loads straight onto typical holders, though printers with very small enclosed spool bays or non-standard hub sizes may need an adapter or external feed.

Poudarki

  • 8 kg total filament gives plenty of material for large projects
  • Silk-like finish creates a glossy, smooth surface on every print
  • Vacuum-sealed spools with desiccant protect filament from moisture
  • 75 mm diameter works with most popular 3D printers
  • Print at 200 °C – 220 °C for reliable extrusion

Specifikacije

BrandPRINTOXE
Color2White+2Orange+2Yellow+2Green
TypePLA Filament like SILK

Vprašanja o tem izdelku

Does the silk PLA filament produce more heat or need higher nozzle power during long prints?

The recommended nozzle temperature is 200°C to 220°C (392°F to 428°F), the same range as standard PLA, so it does not demand extra heat or power for extended printing.

What printer hardware must I already have to use these 1.75 mm spools?

A 3D printer that accepts 1.75 mm filament and spools with a 5.59 cm hub hole, 20.015 cm outer diameter and 6.83 cm width — dimensions that fit most common desktop machines.

Will the filament work on an older printer that only has a basic heated bed and no enclosure?

Yes, the material is designed for standard PLA temperatures and minimal warping, so it prints reliably on older open-frame printers with a heated bed.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.