NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.
A-Tech
A 16GB DDR4 2133MHz CL15 unbuffered DIMM certified for Supermicro systems, using Hynix chips at 1.2V standard voltage
This A-Tech module delivers 16GB of DDR4 memory at 2133MHz with a CL15 latency. It is an unbuffered, non-ECC DIMM built on a Hynix chipset and certified for Supermicro systems. The 288-pin form factor fits standard desktop motherboards that support DDR4 memory.
Replacing an 8GB stick or a slower DDR4 kit with this 16GB module doubles capacity and restores rated 2133MHz speed. The jump is worth it when your workload exceeds current memory limits or when a qualified vendor list requires this specific Supermicro certified part number.
Installation follows the standard 288-pin DIMM procedure: align the notch, press firmly until the retention clips engage, and verify seating. The most common issue is a mismatch between the module specifications and the motherboard qualified vendor list, so confirm supported speeds and capacities before purchase.
| Brand | SuperMicro |
|---|---|
| Series | Supermicro Certified |
| Model | MEM-DR416L-HL01-UN21 |
| Capacity | 16GB |
| Speed | DDR4 2133 (PC4 17000) |
| Tested Frequency | 2133 |
| CAS Latency | CL15 |
| Voltage | 1.20V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major Brand Chipset |
| Heat Spreader | No |
| Features | Supermicro Certified MEM-DR416L-HL01-UN21 (HMA82GU6MFR8N-TF) |
| Recommend Use | Compatible Supermicro Systems |
This module uses the standard 288-pin DDR4 DIMM form factor, so it fits any desktop board with DDR4 slots.
Align the off-centre notch with the key in the slot, press straight down until the side clips click shut on both ends.
The module is built with Hynix chips and carries a lifetime warranty, so under normal desktop use it should not require replacement.
Myös tällä osastolla
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
Valuutta, jolla maksetaan, sekä valuutta, jossa hinnat näytetään.
Lähetetään lompakostasi kassalla
Vain näyttöä varten — hinnat ovat Yhdysvaltain dollareissa
Valuuttaa ei löytynyt.
Valitse kieli, jolla sivusto puhuu sinulle.
Uusi täällä?
Onko sinulla jo tili?
Automaattista palautusta ei ole: kauppa ei lähetä sähköpostia lainkaan, joten kertakäyttöistä linkkiä ei ole mistä pyytää. Jätä osoite tilille, niin se käsitellään käsin.
Pyyntö kirjattu
Mikään ei ole tulossa sähköpostiisi — tämä kauppa ei lähetä sähköpostia lainkaan. Joku käsittelee nämä pyynnöt käsin.
Muistitko sen?