Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with black memory chips and gold edge connectors

A-Tech

A-Tech 16GB DDR4 2933 MHz ECC UDIMM 2Rx8 CL21 1.2V 288-Pin Server RAM

SKU CH-EBYK-JDNCN

16 GB DDR4 ECC UDIMM runs at 2933 MHz with CL21 latency for server and workstation upgrades

  • CAS LatencyCL21
  • Rank2Rx8
  • ECC protection guards data integrity with DDR4 2933 MHz speed
  • 16 GB capacity expands server workloads using a single 288-pin module
  • Dual-rank 2Rx8 architecture increases memory density for demanding tasks
  • CL21 latency and 1.2 V operation balance responsiveness with efficiency
  • Rigorous testing and lifetime warranty back dependable server performance

Server DDR4 16 GB module

This 16 GB DDR4 ECC UDIMM runs at 2933 MHz with CL21 latency and 1.2 V operation. It is built for servers and workstations that require error-correcting unbuffered memory. The dual-rank 2Rx8 organisation fits standard 288-pin DIMM slots. Desktop and laptop systems are not supported.

Replaces non-ECC or lower-capacity sticks

Swapping standard unbuffered DIMMs for this ECC module adds data-integrity protection for critical workloads. The jump is worth it when your platform explicitly lists DDR4 2933 MHz ECC UDIMM support and you need 16 GB per slot. Systems limited to registered memory or lower speeds cannot use this module.

Installs in standard 288-pin slots

Align the notch, press evenly until the latches click, then follow the system manual for channel population order. Common issues arise when mixing ranks or speeds across channels, or when the BIOS does not recognise the 2Rx8 configuration. Verify supported memory specifications before installation.

Kohokohdat

  • ECC protection guards data integrity with DDR4 2933 MHz speed
  • 16 GB capacity expands server workloads using a single 288-pin module
  • Dual-rank 2Rx8 architecture increases memory density for demanding tasks
  • CL21 latency and 1.2 V operation balance responsiveness with efficiency
  • Rigorous testing and lifetime warranty back dependable server performance

Tekniset tiedot

CAS LatencyCL21
Rank2Rx8

Kysymyksiä tästä tuotteesta

Will this 288-pin DDR4 UDIMM fit in my server's standard DIMM slots?

Yes, the module uses the standard 288-pin DDR4 DIMM form factor and 1.2V voltage required by compatible server and workstation motherboards.

What is the correct way to seat this dual-rank ECC module, and what step is often missed?

Align the notch with the slot key, press firmly until both side clips click, then verify the system recognises the full 16GB and ECC function in BIOS.

When should I expect to replace this 2933 MHz CL21 memory?

DDR4 ECC UDIMMs have no moving parts and typically last the life of the server; replace only if memory diagnostics report correctable or uncorrectable errors.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.