Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with black memory chips and gold contacts

A-Tech

A-Tech 4GB DDR3 1333 ECC UDIMM 2Rx8 for Nanya NT4GC72B8PB0NF-CG Server Memory

SKU CH-M2DK-A42N0

A 4GB DDR3 1333 ECC UDIMM module with 2Rx8 rank and 1.5V operation for server memory upgrades

  • Capacity4GB
  • SpeedDDR3 1333 (PC3 10600)
  • CAS LatencyCL9
  • Voltage1.50V
  • ECCYes
  • Buffered/RegisteredUnbuffered
  • ECC protection guards data integrity with built-in error correction
  • 1333 MHz DDR3 speed matches PC3-10600 server specifications
  • 2Rx8 dual-rank layout optimises memory controller efficiency
  • 5 V standard voltage ensures broad platform compatibility
  • 240-pin UDIMM form factor fits DDR3 server slots

4GB DDR3 1333 ECC UDIMM Server Memory

This 4GB DDR3 1333 ECC UDIMM module is built as a compatible replacement for the Nanya NT4GC72B8PB0NF-CG part. It runs at 1333 MHz (PC3-10600) with CL9 latency and standard 1.5V operation. The 240-pin DIMM uses a 2Rx8 organisation and major-brand chips. It targets servers and workstations that require error-correcting unbuffered memory.

Who this suits and who should look elsewhere

This module fits systems that accept DDR3 1333 ECC UDIMM memory in a 240-pin slot. It is not for platforms that require registered or load-reduced DIMMs, nor for boards limited to non-ECC memory. Buyers needing capacities beyond 4GB per slot or speeds above 1333 MHz must select a different part.

The specification that decides fit

The decisive specification is the DDR3 1333 ECC UDIMM 240-pin form factor with 2Rx8 organisation at 1.5V. Only systems that explicitly support this exact combination will recognise and operate the module correctly.

Kohokohdat

  • ECC protection guards data integrity with built-in error correction
  • 1333 MHz DDR3 speed matches PC3-10600 server specifications
  • 2Rx8 dual-rank layout optimises memory controller efficiency
  • 5 V standard voltage ensures broad platform compatibility
  • 240-pin UDIMM form factor fits DDR3 server slots

Tekniset tiedot

BrandA-Tech
SeriesCompatible Replacement for Nanya
ModelNT4GC72B8PB0NF-CG
Capacity4GB
SpeedDDR3 1333 (PC3 10600)
CAS LatencyCL9
Voltage1.50V
ECCYes
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor Brand Chipset
FeaturesNT4GC72B8PB0NF-CG

Kysymyksiä tästä tuotteesta

How do I install this 240-pin DDR3 ECC UDIMM, and what step do people often get wrong?

Align the notch on the module with the key in the 240-pin slot, press straight down until both retention clips click, and verify the system detects 4 GB at 1333 MHz; the common error is inserting the stick at an angle, which can bend pins or leave one clip unlatched.

What maintenance or replacement will this 4 GB 1.50 V DDR3 module need later?

No routine maintenance is required; if errors appear, run a memory diagnostic and replace the module if it fails — ECC corrects single-bit errors but cannot fix a failing chip.

What limit appears first when this 2Rx8 PC3-10600 stick runs under sustained load?

The 1333 MHz data rate and CL9 latency set the bandwidth ceiling; thermal throttling is rare at 1.50 V, so the speed rating is the first bottleneck you will hit.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.