NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.
A-Tech
64 GB DDR4 3200 ECC RDIMM module with 2Rx4 registered design and CL22 latency for server workloads
This 64GB DDR4 3200MHz module is built for servers and workstations that require error-correcting registered memory. It delivers 64GB capacity in a single 288-pin DIMM running at 1.20V with CL22 latency. The 2Rx4 organisation suits high-density configurations where data integrity is critical.
Registered buffering reduces electrical load on the memory controller, allowing larger memory arrays in multi-socket platforms. Major brand DRAM chips are used throughout and every module undergoes quality assurance testing for dependable operation. The standard DDR4 1.2V voltage ensures compatibility with existing DDR4 server power delivery.
Confirm that your motherboard accepts DDR4 registered ECC DIMMs and supports 3200MHz speeds at the required voltage. Systems limited to unbuffered UDIMMs or earlier DDR generations cannot use this module. Check the qualified vendor list or manual for maximum capacity per slot and total system limits.
| Brand | A-Tech |
|---|---|
| Capacity | 64GB |
| Speed | DDR4 3200 (PC4 25600) |
| CAS Latency | CL22 |
| Voltage | 1.20V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 2Rx4 |
| Chipset | Major Brand Chipset |
| Features | Major Brand Chips |
The module runs at 3200 MT/s with CL22 timing at 1.20 V, delivering PC4-25600 bandwidth when the platform supports that speed.
It requires a standard DDR4 288-pin DIMM slot; the registered design adds a buffer chip, so verify the motherboard supports RDIMM and has enough height clearance.
Power off the system, align the notch with the slot key, press firmly until both latches click, then enable ECC in the BIOS — skipping the BIOS step leaves error correction inactive.
Myös tällä osastolla
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
Valuutta, jolla maksetaan, sekä valuutta, jossa hinnat näytetään.
Lähetetään lompakostasi kassalla
Vain näyttöä varten — hinnat ovat Yhdysvaltain dollareissa
Valuuttaa ei löytynyt.
Valitse kieli, jolla sivusto puhuu sinulle.
Uusi täällä?
Onko sinulla jo tili?
Automaattista palautusta ei ole: kauppa ei lähetä sähköpostia lainkaan, joten kertakäyttöistä linkkiä ei ole mistä pyytää. Jätä osoite tilille, niin se käsitellään käsin.
Pyyntö kirjattu
Mikään ei ole tulossa sähköpostiisi — tämä kauppa ei lähetä sähköpostia lainkaan. Joku käsittelee nämä pyynnöt käsin.
Muistitko sen?