Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Pack of ten horizontal JST PH 4-pin connectors, 2mm pitch, 12mm by 7.8mm by 5.6mm

Adafruit

Adafruit JST PH 4-pin Horizontal Connector 10-Pack

SKU CH-XBDR-HS64X

Pack of ten horizontal JST PH 4-pin connectors with 2 mm pitch for plug-and-play prototyping

  • TypePrototyping Products
  • Pack of 10 connectors simplifies multi-point prototyping
  • 2 mm pitch ensures compatibility with JST PH cables
  • Horizontal orientation suits low-profile board layouts
  • Compact 12 mm × 7.8 mm × 5.6 mm body saves PCB space
  • Plug-and-play design speeds up STEMMA wiring tasks

Connector pack for prototyping boards

This pack contains ten JST PH 4-pin horizontal connectors with a 2 mm pitch. They are designed for adding plug-and-play connectivity to custom circuit boards. Each connector measures 12 mm by 7.8 mm by 5.6 mm. The pack suits hobbyists and engineers building prototype hardware.

Behaviour in repeated assembly

The connectors are rated for standard prototyping cycles rather than continuous high-mate industrial use. Horizontal orientation keeps the cable exit low on the board. Contacts maintain reliable connection through repeated plugging and unplugging during development. No STEMMA QT compatibility means they will not mate with smaller JST SH sockets.

Compatibility checks before ordering

Verify that your design uses the 2 mm pitch JST PH footprint and not the smaller JST SH used by STEMMA QT. Ensure the 12 mm by 7.8 mm board footprint fits your layout. Confirm you are using Adafruit JST PH 4 / STEMMA cables or Seeed Grove connectors for mating. These headers are not suitable for STEMMA QT ecosystems.

Kohokohdat

  • Pack of 10 connectors simplifies multi-point prototyping
  • 2 mm pitch ensures compatibility with JST PH cables
  • Horizontal orientation suits low-profile board layouts
  • Compact 12 mm × 7.8 mm × 5.6 mm body saves PCB space
  • Plug-and-play design speeds up STEMMA wiring tasks

Tekniset tiedot

TypePrototyping Products

Kysymyksiä tästä tuotteesta

Does the 2 mm pitch connector generate any heat or noise when used continuously in a prototype?

The connector is a passive component with no active electronics, so it produces no heat or audible noise during continuous use.

What cables or boards must I already have to use these 10 horizontal JST PH 4-pin connectors?

You need Adafruit JST PH 4 / STEMMA cables or a PCB with matching 2 mm pitch footprints; the connectors are not compatible with STEMMA QT (JST SH) cables.

Can I plug these 12 mm × 7.8 mm × 5.6 mm horizontal connectors into older Seeed Grove cables I already own?

Yes, Seeed Grove connectors fit the JST PH 4-pin footprint, so your existing Grove cables will mate with these horizontal connectors.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.