Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
UV-black PVC tubing coil 11/8mm 3m length

Alphacool

Alphacool AlphaTube HF 11/8mm UV Black 3m tubing

SKU CH-F96K-QY31P

UV-reactive PVC tubing with 8 mm inner diameter and 11 mm outer diameter, supplied in a 3 m length that resists kinking during tight bends

  • TypeTubing
  • Installs easily with perfect flexibility for tight bends
  • Resists kinking thanks to balanced rigidity at 65-70 A-Shore
  • Handles system heat from -10 to 80 °C
  • UV-active black finish glows under UV lighting
  • Three-metre length covers full-loop routing

Alphacool AlphaTube HF 11/8mm UV Black 3m

This PVC tubing is made for custom water-cooling loops and comes in a UV-reactive black finish. It ships as a single 3 metre length with an 11 mm outer diameter and 8 mm inner diameter, matching 11/8 mm compression fittings. The material carries a 65-70 Shore A hardness rating for a balance of pliability and shape retention. Builders who want a coloured, UV-active run will find it suited to their aesthetic goals.

Flexibility and kink resistance limits

The hose is flexible enough to route without force, yet rigid enough to resist kinking at tighter bending radii. Its working pressure is rated at 2 bar with a burst pressure of 8 bar, and it operates between -10 °C and 80 °C. Loops that run higher pressures or temperatures exceed the rated envelope. Installers who need extreme tight bends without any deformation should verify the minimum radius against their layout.

Capacity and headroom for typical loops

A single 3 metre pack covers most single-loop builds with CPU and GPU blocks, leaving a small margin for routing errors. Larger configurations with multiple radiators, distribution plates or parallel runs will likely require a second pack. The 8 mm inner diameter supports standard flow rates for common D5 or DDC pumps. Systems demanding higher flow through restrictive blocks may need larger-bore tubing instead.

Kohokohdat

  • Installs easily with perfect flexibility for tight bends
  • Resists kinking thanks to balanced rigidity at 65-70 A-Shore
  • Handles system heat from -10 to 80 °C
  • UV-active black finish glows under UV lighting
  • Three-metre length covers full-loop routing

Tekniset tiedot

TypeTubing

Kysymyksiä tästä tuotteesta

Should I pick the 11/8mm size or a different diameter?

Choose 11/8mm when your fittings are made for 11mm outer and 8mm inner diameter; other sizes will not seal on these barbs.

What does the 65-70 Shore A hardness mean once the tube is in my loop?

It gives a firm yet pliable feel that resists kinking on tight bends while still pushing onto barbs without excessive force.

The spec lists 8 bar burst and 2 bar working pressure — what does that cap in practice?

Normal loop pressure stays well below 2 bar, so the 8 bar burst rating provides a wide safety margin against accidental over-pressure.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.