Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Alphacool Eiszapfen 16mm 45° compression fitting deep black knurled finish

Alphacool

Alphacool Eiszapfen 16mm 45° HardTube Compression Fitting Deep Black 1013356

SKU CH-T2BS-SWKB7

A 45° compression fitting for 16mm hard tubes in acrylic, brass, borosilicate or carbon with a durable Deep Black finish

  • Fan ColorBlack
  • FeaturesNew fitting from Alphacool for acrylic, brass, borosilicate

Size 16mm

  • 16 mm hard-tube compression fitting for secure liquid cooling loops
  • 45° angled L-connector enables tidy routing in tight chassis spaces
  • Deep Black finish resists fading and peeling for lasting appearance
  • Compatible with acrylic, brass, borosilicate glass and carbon tubes
  • Alphacool branding on fitting and collars adds professional build aesthetic

Fitting Specifications

The Alphacool Eiszapfen 1013356 is a 45° compression fitting designed for 16mm outer diameter hard tubing. It accepts acrylic, brass, borosilicate glass or carbon tubes in custom liquid-cooling loops. A knurled collar allows tool-free tightening and the Deep Black finish resists fading.

Loop Build Suitability

This part suits builders assembling a custom water-cooling loop who need a 45-degree directional change with 16mm hard tube. It is not for anyone using soft tubing, smaller or larger tube diameters, or push-to-connect fittings.

Deciding Specification

The defining parameter is the 16mm hard-tube compression interface combined with a 45° angle. Only loops built around 16mm OD rigid tubing can use this fitting; any other tube size or fitting type will not seal correctly.

Kohokohdat

  • 16 mm hard-tube compression fitting for secure liquid cooling loops
  • 45° angled L-connector enables tidy routing in tight chassis spaces
  • Deep Black finish resists fading and peeling for lasting appearance
  • Compatible with acrylic, brass, borosilicate glass and carbon tubes
  • Alphacool branding on fitting and collars adds professional build aesthetic

Tekniset tiedot

BrandAlphacool
Model1013356
Fan ColorBlack
FeaturesNew fitting from Alphacool for acrylic, brass, borosilicate (glass) or carbon tubes. Alphacool takes another step towards perfection and quality.

Tämän mallin muut versiot

1 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

How do I install the 16mm 45° compression fitting on hard tubing without leaks?

Cut the tube square, deburr the inside edge, slide the collar then the compression ring onto the tube, push the tube fully into the fitting body until it seats, and tighten the collar by hand plus a quarter turn with a wrench; the step most people miss is not pushing the tube all the way to the internal stop before tightening.

What maintenance or replacement will the Deep Black finish on the 1013356 fitting need later?

The new application process prevents fading or peeling, so the finish requires no recoating; only inspect the O-rings during routine loop maintenance and replace them if they show cracking or compression set.

What limit appears first on the 16mm 45° L-connector under sustained use?

The 45° bend radius restricts flow more than a straight fitting, so pressure drop across the elbow becomes the limiting factor before the compression seal or finish degrades.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.