Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Chrome 45-degree rotatable compression fitting with knurled nut for 16mm hard tube G1/4 thread

Alphacool

Alphacool Eiszapfen 16mm HardTube Compression Fitting 45° Rotatable G1/4 Chrome 17408

SKU CH-Q5MB-QHN3H

A 45° rotatable compression fitting for 16 mm hard tube with G1/4 thread and chrome finish

  • TypeFittings
  • Secure 16mm HardTube connection with knurled union nut
  • 45° rotatable angle simplifies tight routing
  • G1/4 thread fits 95% of water-cooling components
  • Durable chrome coating resists chipping and peeling
  • High-flow design maintains efficient coolant circulation

High-Flow Chrome Fitting

The Alphacool Eiszapfen 16mm HardTube compression fitting connects 16mm acrylic or brass tubing to any G1/4 port. Its rotatable 45° design simplifies routing in custom liquid-cooling loops. The chrome finish resists chipping and peeling for long-lasting appearance.

Leak-Secure Construction

Slanted corners on the union nut press the O-ring firmly against the hard tube for a reliable seal that withstands transport vibration. The high-flow internal geometry minimises restriction while maintaining secure connections throughout the loop.

Universal G1/4 Compatibility

The 1/4-inch thread fits 95 percent of water-blocks, radiators, reservoirs and pumps on the market. Rotatable threading allows final alignment after installation without stressing the tube. One fitting is supplied per package.

Kohokohdat

  • Secure 16mm HardTube connection with knurled union nut
  • 45° rotatable angle simplifies tight routing
  • G1/4 thread fits 95% of water-cooling components
  • Durable chrome coating resists chipping and peeling
  • High-flow design maintains efficient coolant circulation

Tekniset tiedot

TypeFittings

Kysymyksiä tästä tuotteesta

How do I install the 16 mm hard tube into this 45° rotatable G1/4 compression fitting and what step do people often miss?

Slide the union nut and compression ring onto the tube, push the tube fully into the fitting until it seats against the internal stop, then tighten the knurled nut by hand plus a quarter turn with a wrench; the step most people miss is confirming the tube is bottomed out before tightening, otherwise the O-ring will not seal properly.

What maintenance or replacement will this chrome-finished fitting need over time?

The bonded chrome coating resists chipping and peeling, so the fitting body itself rarely needs replacement; plan to inspect and, if necessary, replace the internal O-ring whenever you drain the loop or notice any seepage at the 16 mm tube connection.

What is the first limit I will hit when running this 45° rotatable fitting under sustained flow?

The 45° bend introduces a modest flow restriction compared with a straight fitting, so under sustained high-flow operation the pressure drop across the elbow becomes the limiting factor before the G1/4 thread or the 16 mm tube seal reach their limits.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.