Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black brass 45-degree G1/4 female-female adaptor, compact L-shape with matte finish

Alphacool

Alphacool Eiszapfen 45° G1/4 Female-Female Adaptor Black Brass 17592

SKU CH-CH3K-71DT3

A 45° brass adaptor with dual G1/4 female threads routes tubing in tight water-cooling loops

  • ColorBlack
  • FeaturesThis 45 angled adapter has a G1/4" female thread on both sid

Color Black

  • 45° angle routes tubing in tight spaces with G1/4" female threads both ends
  • Brass construction resists corrosion and handles high-flow custom loops
  • Matte black coating bonded to surface prevents chipping or peeling over time
  • Compact 21 mm × 20 mm × 21 mm body fits confined water-cooling layouts
  • Weighs 17 g adding minimal mass to the cooling assembly

Compact 45° G1/4 Female Adaptor

The Alphacool Eiszapfen 45° adaptor connects two G1/4 female threads at a fixed forty-five-degree angle. Its brass body measures twenty-one by twenty by twenty-one millimetres and weighs seventeen grams. The matte black coating resists chipping through a specialised bonding process. It suits custom-loop builders routing tubing in confined spaces.

Replaces Rigid Straight Fittings

Swap a straight bulkhead or elbow when tubing must bend sharply against a component or panel. The forty-five-degree offset clears obstacles that a ninety-degree fitting cannot, while keeping the flow path smoother than a tight tube bend. The gain is worthwhile only when the routing angle matches the fixed geometry.

Steady Flow Under Load

The high-flow internal bore maintains consistent coolant velocity during prolonged pump operation. Brass construction conducts heat away from the fluid without deforming under typical loop temperatures. The fixed thread depth of five millimetres on each side ensures a reliable seal that does not relax over time.

Kohokohdat

  • 45° angle routes tubing in tight spaces with G1/4" female threads both ends
  • Brass construction resists corrosion and handles high-flow custom loops
  • Matte black coating bonded to surface prevents chipping or peeling over time
  • Compact 21 mm × 20 mm × 21 mm body fits confined water-cooling layouts
  • Weighs 17 g adding minimal mass to the cooling assembly

Tekniset tiedot

BrandAlphacool
Model4250197175920
ColorBlack
FeaturesThis 45 angled adapter has a G1/4" female thread on both sides. This 45 angled connection is used in water circuits where there is limited space for tubing and a special solution is needed.

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

How much clearance do the 21 mm height and 20 mm width need inside the case?

The adaptor measures 21 mm tall by 20 mm wide, so allow at least that much space around the G1/4 female ports for the fittings you will thread into it.

Which way do I thread the two G1/4 female ports, and what torque is safe for the 5 mm thread depth?

Screw each male G1/4 fitting into the female ports by hand until snug, then give a light quarter-turn with a wrench; the 5 mm thread depth seats fully without bottoming out.

Will the black coating on the brass body wear off when I disassemble the loop for maintenance?

A special binding process locks the matte black finish to the brass, so repeated fitting removal does not cause chipping or peeling.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.