Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Chrome 90-degree compression fitting with knurled collars for 13mm hard tube

Alphacool

Alphacool HT 13mm HardTube Compression Fitting 90° Elbow Chrome 17295

SKU CH-SQY5-GPYG7

Connects 13 mm hard tubes at a 90° angle with a knurled chrome compression fitting for custom liquid-cooling loops

  • TypeFittings
  • 90° elbow routes hard tubing cleanly in tight spaces
  • 13 mm compression fitting seals acrylic, brass, borosilicate or carbon tubes
  • New application process resists finish fading and peeling
  • Knurled chrome collars add grip and a professional look
  • Alphacool branding on fitting and collars completes a coordinated build

Alphacool HT 13mm HardTube 90° Elbow

This chrome compression fitting connects 13mm outer-diameter hard tubes at a right angle. It suits builders creating custom liquid-cooling loops with acrylic, brass, borosilicate or carbon tubing. The knurled collars provide secure grip for leak-free joints in high-end workstation or enthusiast builds.

Installation notes and common pitfalls

Push the tube fully into the fitting until it seats against the internal stop, then hand-tighten the knurled collar; no tools are required. The most frequent error is cutting the tube end unevenly or leaving burrs, which prevents a proper seal and causes drips under pressure.

Capacity and headroom

One 90° elbow redirects a single 13mm tube run without restricting flow in typical custom loops. It cannot join tubes of a different diameter, nor does it replace straight couplings or angled rotary adapters when the layout demands those geometries.

Kohokohdat

  • 90° elbow routes hard tubing cleanly in tight spaces
  • 13 mm compression fitting seals acrylic, brass, borosilicate or carbon tubes
  • New application process resists finish fading and peeling
  • Knurled chrome collars add grip and a professional look
  • Alphacool branding on fitting and collars completes a coordinated build

Tekniset tiedot

TypeFittings

Kysymyksiä tästä tuotteesta

How can I verify the 90° elbow is seated correctly after installing 13mm hard tube?

The knurled compression collars should sit flush against the tube with no visible gap and the chrome finish should show no deformation once the fitting is tightened by hand plus a quarter turn.

What comes in the package and do I need extra collars or tools for 13mm acrylic or brass tube?

The box contains one 90° elbow fitting with pre-installed knurled collars; no additional collars or special tools are required for 13mm acrylic, brass, borosilicate or carbon tubes.

Should I choose the Chrome or Deep Black version for a build using Alphacool Plexi brass tubes?

Both finishes use the same new application process that resists fading; select Chrome for a bright metallic accent or Deep Black for a stealth look — either matches the Plexi brass tube series.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.