Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Six chrome knurled compression fittings for 13mm hard tube G1/4 thread

Alphacool

Alphacool HT 13mm HardTube Compression Fitting G1/4 Chrome 6-Pack

SKU CH-7T2K-XGZNA

Six chrome compression fittings connect 13 mm hard tubes to G1/4 threads with dual O-ring seals

  • TypeFittings
  • Leak-tight seal with dual O-ring design
  • Fits 13mm outer-diameter hard tubes
  • G1/4 thread connects to standard water-cooling parts
  • Knurled union nut allows tool-free hand tightening
  • Chrome finish resists corrosion and matches loop aesthetics

Alphacool HT 13mm HardTube Fittings

The Alphacool HT compression fittings provide secure G1/4 connections for 13mm outer-diameter hard tubes. Each chrome-plated fitting uses dual O-rings and a protective plastic disc to ensure a reliable seal. The knurled union nuts allow straightforward hand-tightening, while an 8mm Allen key secures the base. This six-pack supplies enough fittings for a typical custom loop build.

Builders using 13mm rigid tubing

These fittings suit builders assembling custom water-cooling loops with 13mm plexi or brass tubes who need a chrome finish. They are not intended for soft tubing, push-fit installations, or metric thread standards other than G1/4. Buyers requiring angled or rotary adapters, different tube diameters, or a black finish should select alternative models.

Verify tube diameter and thread compatibility

Confirm that your hard tubes measure exactly 13mm outer diameter and that all components in your loop use G1/4 threads. Check available clearance around each port to accommodate the fitting body and union nut. Ensure you have an 8mm Allen key for final tightening of the fitting base during assembly.

Kohokohdat

  • Leak-tight seal with dual O-ring design
  • Fits 13mm outer-diameter hard tubes
  • G1/4 thread connects to standard water-cooling parts
  • Knurled union nut allows tool-free hand tightening
  • Chrome finish resists corrosion and matches loop aesthetics

Tekniset tiedot

TypeFittings

Kysymyksiä tästä tuotteesta

What tube diameter do I need to use with these 13 mm compression fittings?

They are designed for hard tubes with a 13 mm outer diameter, whether plexi or brass.

Will the G1/4 threads on these fittings match the ports on my existing water blocks and radiators?

Yes, the G1/4 thread is the standard size used on almost all custom-loop components.

How can I confirm each fitting is sealed properly after I tighten the union nut with an 8 mm Allen key?

Pressurise the loop and watch for drips; the dual O-rings and protected seating should give a completely dry joint.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.