Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Blue silicone bending insert for 13mm hard tubing, 150cm length

Alphacool

Alphacool Silicon Bending Insert 13mm 150cm Blue

SKU CH-FG2S-Y6DVS

Silicone insert prevents kinking when heat-bending 13 mm hard tubing, 150 cm length

  • TypeTubing
  • ColorBlue
  • FeaturesFor perfect bends in the Alphacool HardTubes now there is th
  • Heat-resistant silicone prevents kinking when bending 13mm hard tubing
  • 150cm length suits long tubing runs and complex loops
  • Insert slides inside tube for internal support during heating
  • Removes easily after cooling for clean finished bends
  • Compatible with Alphacool HardTubes in 10mm 12mm and 13mm inner diameters

Silicone Insert for 13mm Hard Tubing

This Alphacool silicone insert is designed for bending 13mm inner-diameter hard tubing in custom water-cooling loops. The heat-resistant silicone prevents kinking at the curved point while the tube is heated. After the bend cools the insert can be removed easily. It suits builders shaping longer HardTube runs.

Installation and Common Issues

Slide the 150cm insert fully inside the hard tube before applying heat to the bend area. The silicone withstands the temperature required for forming so the tube keeps a smooth radius. A frequent mistake is heating a section that is not supported by the insert which can cause the wall to collapse. Ensure the insert covers the entire curve.

Who This Suits and Who Should Look Elsewhere

The 150cm length suits builders forming curves in longer pipe sections. Shorter 30cm or 100cm versions exist for tight bends in short pipes. Buyers working with 10mm or 12mm inner-diameter tubing need the matching diameter insert. This product is only the bending aid not the hard tubing itself.

Kohokohdat

  • Heat-resistant silicone prevents kinking when bending 13mm hard tubing
  • 150cm length suits long tubing runs and complex loops
  • Insert slides inside tube for internal support during heating
  • Removes easily after cooling for clean finished bends
  • Compatible with Alphacool HardTubes in 10mm 12mm and 13mm inner diameters

Tekniset tiedot

BrandAlphacool
Model1015255
TypeTubing
ColorBlue
FeaturesFor perfect bends in the Alphacool HardTubes now there is the perfect solution.

Kysymyksiä tästä tuotteesta

How can I confirm the silicone insert is correctly positioned inside the 13mm hard tube before heating?

Push the 150cm blue silicone insert fully into the Alphacool HardTube until it reaches the bend zone; the tube should feel evenly supported along the heated section with no gaps.

What comes in the package and what must I supply myself?

The box contains one 150cm blue silicone bending insert (model 1015255); you must provide 13mm (1/2") ID Alphacool HardTubes and a heat source such as a heat gun.

Which insert length matches a long-radius bend in a full-loop build?

Choose the 150cm length for curves in longer pipes; the 30cm and 100cm versions are meant for shorter tubing runs.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.