Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Silver rectangular 2U redundant server power supply with modular cable connectors

Athena Power

Athena Power AP-RRU2MK1262 1200W 2U CRPS Redundant Server Power Supply

SKU CH-RSWP-3YDT6

Redundant 2U CRPS server power supply delivering 1200W with 80 PLUS and 62368 safety certification

  • TypeRedundant
  • Single/RedundantRedundant
  • Maximum Power1200W
  • Main Connector24Pin
  • Output Current+3.3V@12A, +5V@24A, [email protected] , +5Vsb@5A, [email pro
  • Output+3.3V, +5V,+12V, +5Vsb, -12V
  • 250,000-hour MTBF ensures long-term server reliability
  • 94%+ efficiency reduces operating costs and heat
  • IEC 62368 safety certification meets global compliance needs
  • 2U CRPS modular design enables hot-swap redundancy
  • 1200 W total output powers dense multi-GPU workloads

Redundant 2U server power supply

The Athena Power AP-RRU2MK1262 is a redundant 2U form factor switching power supply designed for servers, workstations and industrial automation equipment. It delivers a total capacity of 1200 Watts across two hot-swap modules. PMBus control allows the motherboard to monitor power status in real time. The unit meets 80 Plus Platinum efficiency and 62368 safety certification for worldwide compliance.

1200 W capacity with full-range input

Each module supplies up to 1200 W with output rails at +3.3V, +5V, +12V, +5Vsb and -12V. The supply operates on 90 to 264 Volts AC at 47 to 63 Hz, drawing 8 to 4 Amps depending on line voltage. Efficiency exceeds 94 percent under typical loads. Hold-up time is 11 ms minimum at nominal input, and protections include OCP and OVP. The design supports continuous full-load operation up to 55 °C.

Bundled cables cover ATX 3.1 and PCIe 5.0

Included connectors are a 24-pin ATX, two 8-pin EPS12V, eight 6+2-pin PCIe, six SATA and two floppy power plugs. A 12V-2x6 cable is supplied for ATX 3.1 compliance and PCIe 5.0 graphics support. This cable set lets the supply power modern multi-GPU servers without extra adapters. Builders needing different connector counts or form factors must source alternative units.

Kohokohdat

  • 250,000-hour MTBF ensures long-term server reliability
  • 94%+ efficiency reduces operating costs and heat
  • IEC 62368 safety certification meets global compliance needs
  • 2U CRPS modular design enables hot-swap redundancy
  • 1200 W total output powers dense multi-GPU workloads

Tekniset tiedot

BrandAthena Power
ModelAP-RRU2MK1262
TypeRedundant
Single/RedundantRedundant
Maximum Power1200W
Main Connector24Pin
Output Current+3.3V@12A, +5V@24A, [email protected] , +5Vsb@5A, [email protected]
Output+3.3V, +5V,+12V, +5Vsb, -12V
Input Voltage90 ~ 264 Volts AC
Input Frequency Range47 ~ 63 Hz
Input Current100~240V, 8 ~ 4A, 50~60Hz
MTBF250,000 Hours on Maximum Load at +25 degree C
Efficiency>94%
Hold-up Time11 ms Minimum at Nominal Input Voltage
ProtectionOCP, OVP,
FeaturesRise time: Less than 70 ms
Dimensions(L x W x H) 264 x 76 x 83.8 mm/ 10.4 x 3 x 3.3 in
Weight10.00 lbs
Humidity20%-90%
TemperatureOperating: 0°C ~ +55°C on Full Load; Storage & Shipping: -40°C ~ +70°C

Kysymyksiä tästä tuotteesta

Will the 1200W redundant unit fit and power my existing 2U server chassis that uses a 24-pin ATX and dual EPS 8-pin connectors?

Yes, the supply uses the CRPS 2U form factor (264 x 76 x 83.8 mm) and provides a 24-pin ATX connector plus two EPS 12V 8-pin connectors, matching standard 2U server backplanes.

How can I confirm the PMBus monitoring is active once the supply is installed?

The PMBus interface communicates with the motherboard; you can verify operation by reading voltage, current and temperature sensors through the server management software or BMC interface.

Which cables are included and what must I source separately for a full build?

The package includes a 12V-2x6 cable for ATX 3.1 and PCIe 5.0 support; all other modular cables (PCIe 6+2-pin, SATA, floppy) are supplied, so no extra cables are required for typical server configurations.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.