Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black rectangular ATX power supply with matte finish and 140mm fan grille

Baibo

Baibo 3600W ATX 12V 2.31 12 GPU 80 PLUS Bronze power supply

SKU CH-6S4J-2VQN2

Delivers 3600 W through twelve 6+2-pin GPU connectors and eight 12 V rails with 80 PLUS Bronze efficiency and active PFC

  • ColorBlack
  • TypeATX 12V
  • PFCPassive
  • Main Connector20+4Pin
  • +12V Rails8
  • SATA Power Connector2
  • 3600W output powers up to 12 graphics cards
  • ATX 12V 2.31 supports latest Intel and AMD processors
  • 80 PLUS Bronze certification with 90% efficiency
  • 140mm ball-bearing fan and grill for strong cooling
  • 24 six-plus-two-pin and 7 SATA connectors for multi-GPU rigs

High-density mining power

This 3600W ATX 12V 2.31 unit delivers 3600W continuous output through eight +12V rails and twenty-four 6+2-pin connectors, built for rigs that run twelve graphics cards from a single supply. Passive PFC and an input range of 110-240V let it operate on standard mains worldwide without extra switching gear.

Replacing multi-PSU stacks

A single 295 x 185 x 85 mm chassis removes the need to chain two or three smaller supplies together, cutting cable clutter and eliminating the sync boards that often fail under load. The jump is worth it when a build moves past eight cards and the existing wiring loom becomes a heat and reliability bottleneck.

Build integration needs

Full modular output lets you connect only the eight IDE, seven SATA and twenty-four PCIe leads the rig actually uses, freeing case space and airflow for the cards themselves. A 140mm ball-bearing fan exhausts heat through the rear grille, so the chassis must allow straight-through rear ventilation; no side-panel mesh or top-mount clearance is required.

Kohokohdat

  • 3600W output powers up to 12 graphics cards
  • ATX 12V 2.31 supports latest Intel and AMD processors
  • 80 PLUS Bronze certification with 90% efficiency
  • 140mm ball-bearing fan and grill for strong cooling
  • 24 six-plus-two-pin and 7 SATA connectors for multi-GPU rigs

Tekniset tiedot

ColorBlack
TypeATX 12V
PFCPassive
Main Connector20+4Pin
+12V Rails8
SATA Power Connector2
Efficiency> 90%
Energy-Efficient80 PLUS BRONZE Certified
Over Voltage ProtectionYes
Overload ProtectionYes
Input Voltage110 - 240 V
Power Rating240W

Kysymyksiä tästä tuotteesta

What case dimensions are required to fit the 295 × 185 × 85 mm power supply?

The unit measures 295 mm long, 185 mm wide and 85 mm high, so the case must provide at least that much clearance in each direction.

Which cables must be connected during installation, and which step is often missed?

Connect the 20+4 pin main connector, the 24 × 6+2 pin GPU cables, 8 IDE plugs and 7 SATA plugs; the step most often missed is seating every 6+2 pin connector for all 12 graphics cards.

When should the 140 mm ball-bearing fan be cleaned or replaced?

Clean dust from the fan grill every few months; replace the fan if bearing noise appears or airflow drops noticeably.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.